Remote Rig

RRC 1258 Support in English => General discussion forum => Topic started by: dl5mgd on 2011-12-11, 21:27:32

Title: IC706MK2g and Computer control via HRD
Post by: dl5mgd on 2011-12-11, 21:27:32
Hello all,
I am using an Icom706Mk2g with the control panel here in my shack and the trcvr at the remoteside 30 km away. All is working fine. Now I want to connect from my shack with HRD to the trcvr at the remote side. I am using the USB connector in the shack and told the control panel to use com2 and to activate usb as com 2.
What do ihave to do at the trcvr side? Do i need special cabling at the trcvr end?
Thanks a lot!!!
73
Andreas
 
Title: Re: IC706MK2g and Computer control via HRD
Post by: SM0SHG on 2011-12-12, 10:39:18
You will need a CI-V cable between the radio and the remoterig unit.
Regards,
Adde
Title: Re: IC706MK2g and Computer control via HRD
Post by: dl5mgd on 2011-12-13, 17:39:22
Thanks,
i installed a ci-v cable at the remote side today.
Computercontrol is not working as before and at my control panel i can only power up the trcvr, so that i can hear stations; i can tune with the tune knob but i do not have any signs at my display, the display ist black.
Big problems now, bigger than before.
73
Andreas
Title: Re: IC706MK2g and Computer control via HRD
Post by: dj4mz on 2011-12-15, 16:08:12
Hi Andreas,

I don't know the details of your cabling but I also have had the problem with the "dark" display. It took quite some time to find out, but in my case the problem was caused by a loose contact at the RJ45 connector for the control panel!

BTW: I also use the control panel and an additional CI-V connection for CAT-control.

vy 73
Simon, DJ4MZ
Title: Re: IC706MK2g and Computer control via HRD
Post by: M0BPQ on 2011-12-17, 13:32:17
I also have the "dark panel" problem with my 706G, but audio, cw keying etc is being transferred jsut fine. Funnily enough this happened to me after I tried to config computer control as well. I know my cables are still good as I just tested them with a back to back RJ45 adapter....

please post if you find the answer to your problem and I will do likewise.
73
Steve
M0BPQ
Title: Re: IC706MK2g and Computer control via HRD
Post by: dl5mgd on 2011-12-18, 11:42:33
Hello,
problems solved.
The problem was the IC706 itself
In the initial set mode (number 36 CI-V TRN) the setting was "on"; strange behaviour. I changed this to "off" and all is working fine.

73
Andreas
 
Title: Re: IC706MK2g and Computer control via HRD
Post by: M0BPQ on 2011-12-19, 18:31:38
Pleased to see you have your system working.

I am afraid mine is not though. I turned off the CIV as you sugessted with no change. Then did a factory CPU reset, with no change.

To recap. The face works fine locally when my RRC cables are joined using a back to back adapter and plugged into the 706, but I get nothing on the face plate when connecting over my LAN via the RRCs. Tuning, audio, cw etc are all fine. I have just updated the FW to the latest release. Any ideas where I am going wrong or what I can test, readers?

73
Steve
M0BPQ
Title: Re: IC706MK2g and Computer control via HRD
Post by: sm2o on 2011-12-19, 19:27:41
Hi

The data signal from radio to panel is missing somewhere. It can be one the red straps which is broken or the ic706 cable.Even if it they work connected directly it can be a problem with the data-gnd in the cable. If you email me login data I can try to connect from here to determine if it's in the control or radio end you have the problem.

73 de mike
Title: Re: IC706MK2g and Computer control via HRD
Post by: dj4mz on 2011-12-20, 16:14:09
Hi Andreas!

The problem was the IC706 itself
In the initial set mode (number 36 CI-V TRN) the setting was "on"; strange behaviour. I changed this to "off" and all is working fine.

Great to hear that your setup is working now, but I'm a little bit confused about the explanation. I have CI-V Transceive turned on in my setup and that works great. I like to see my bandmap move in real-time!

vy 73
Simon, DJ4MZ
Title: Re: IC706MK2g and Computer control via HRD
Post by: M0BPQ on 2011-12-21, 15:47:35
For public info - I am using RRC v1 boxes so no strap problems. The RRC- face and RRC- radio cables check out fine from pins 1-8 for continuity and pin to pin connectivity as per the manual. I have sent my system details to Mike so that he can try a remote login. A but stuck why this has stopped working after several months....

Once I have the face back illuminated, I will need to look at the CIV issues  ;)
73
Steve
M0BPQ
Title: Re: IC706MK2g and Computer control via HRD
Post by: EI3KD on 2012-05-09, 09:55:36
@Steve M0BPQ - I know this is an old topic, but did you get your setup working? I have the same problems as you describe, using v1 boxes and an IC706MK2 - would be interesting to know if you found a fix!

Mark EI3KD