Remote Rig
RRC 1258 Support in English => Configuration, RRC 1258 => Topic started by: ja3aop on 2011-12-30, 13:49:31
-
Hello, My RRC 1258 for ICOM706G detachable panel connection worked well via LAN.
Last week, I tried to control from remote site via internet connection with ddns. I set ddns parameters to RRC cont. and RRC radio as stated in manual. Unfortunately I got no connection with my radio.
Also, my serial number are less than 3300, as discussed in VE2EO's case.
Please help me with some advices to solve this problem.
Thank you. 73
ja3aop Akira
RRC control Firmware version = 2.050 Serial # = 2155
RRC Radio Firmware version = 2.050 Serial # = 2185
-
Akira-san,
Are you using the DynDNS service, or the new one from RemoteRig included in firmware 2.50?
73,
Mitch DJ0QN / K7DX
-
Mitch-san,
Thank you for your prompt reply.
I am using new ddns.remoterig.com.
73. ja3aop/Akira
-
Akira-san,
Then it should work ok. Maybe the manual was not clear enough, here is an extract from my checklist that I send
to help in new installations:
- Go to the Dynamic DNS settings tab (radio RRC only)
- Change the check interval to i.e. 10 minutes
- Make sure the drop-down is on RemoteRig's service
- Click on apply changes
The Microbit Dynamic DNS address is entered automatically into the "own host name" field if you use this service.
On the control RRC, place the information from the radio RRC's "own host name" on the Radio Settings tab under SIP contact. When testing at the same QTH as the radio, you should temporarily place the radio RRC's internal IP number into this field, just don't forget to change it when you take the RRC with you. Note that this address is WITHOUT a port suffix (like :1234), since the port is entered into the SIP contact field separately. Everything should work now. Just don't forget to use the Dynamic DNS address when not at the station, this is the #1 cause of the system not working when leaving your local network this first time!
73 & HNY,
Mitch DJ0QN / K7DX
-
Mitch-san
Thank you for your detail guide for me.
Before my traial I did those setup and changes.
- Go to the Dynamic DNS settings tab (radio RRC only) : Yes
- Change the check interval to i.e. 10 minutes : Yes
- Make sure the drop-down is on RemoteRig's service : Yes (ddns.remoterig.com)
- Click on apply changes : apply change was done
The Microbit Dynamic DNS address is entered automatically into the "own host name" field if you use this service.
Yes, I will try again tomorrow more carefully.
73. Happy New Year
ja3aop AKIRA
-
I tried RRC connection via internet with ddns.remoterig.com before yesterday.
Status of RRC-cont. at remote site was as below. It was looked like well.
Status (before trial)
Name Value
Control panel OFF
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status OK, xxxxxxxx.ddns.remoterig.com = 112.68.223.161
Active profile: Default
PTT status: OFF
Program mode was 2-IC706.
I pushed the POWER SW on detached front panel of IC-706MK2G.
After about 10 sec., IC-706 became beeping [puuu pooo piiii ], [puuu pooo piiii ], .......
The front panel did not light on, failed to power on.
AUX/MIC yellow LED was blinking.
When RRC-cont. was restarted, PWR green LED of RRC-cont was binking.
After this trial, status of RRC-cont. was as follows.
Status (after trial)
Name Value
Control panel OFF
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status Error, failed to resolve xxxxxxxx.ddns.remoterig.com!
Active profile: Default
PTT status: OFF
After this trial, PCs on same LAN ware able to connect internet. I turned off my rooter to reset it. Then PCs became able to connect internet.
And status of RRC-cont came back to before trial.
Please, any ideas for this problem.
Thank you.
73.
ja3aop/AKIRA
-
Akrira-san,
I assume the first listing is the radio RRC and the second the control RRC?
Assuming that is correct, then were these within the same LAN at the time you tried the
tests? If they are within the same LAN, you should not use the dynamic DNS address in
the control RRC's SIP contact field, but use the internal IP address. Sometimes using the
dynamic DNS address works, but often it doesn't. Only use the Dynamic DNS address in
the control RRC's SIP contact field when not within the same LAN.
If that isn't the problem, then I am not sure how to interpret the situation, I would need
to take a look over Teamviewer or find some way to help otherwise. Or maybe Mike sees
something I don't.
73,
Mitch DJ0QN / K7DX
-
Mitch-san,
1st one is for RRC-cont. before pushing the power SW on IC-706 front panel.
2nd one is for RRC-cont. after pushing the power SW.
As I stated at the beginning of this thread, Remoterig 1258 pair work well on same LAN.
Problem is caused on internet connection.
I like to print here more detail status report of the Remoterig 1258.
---------------------------------------------
1) RRC-Radio (at my home)
Info
Name Value
Company Microbit
Product 1258
PID 0
Hardware 5
Software 2.50
Bootloader <= 1.7
Compiler 4.1.2 (WinARM 4/2007)
Build Dec 15 2011 15:15:54
ROM/RAM 372540/50740
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 2509
Serial number 2185
MAC address 00:1e:fd:01:7f:29
IP address 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Settings
Unit ID (Banner)
DHCP 0
IP 192.168.1.228
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host 112.68.223.161
Eth-type 5
Web page user
Web page pwd
Program mode 2
Control panel 0
Sip password yyyyyyyy
Sip contact
Auto connect 0
Audio quality 2
Audio dual-rx 0
Codec out gain 255
Codec inp gain 0
Codec inp HPF Hz 3
Codec inp preamp 1
COM0 baudrate 19200
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 19200
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 19200
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5060
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
Continuous RTP tx 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Dynamic DNS check interval 10
Dynamic DNS host name 1
Own host name xxxxxxxx.ddns.remoterig.com
Username rrc1258-2185
Password yyyyyyyy
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,500-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
Status
Name Value
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
External IP 112.68.223.161
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status OK
Ping status (watchdog) Off
DNS status OK, remoterig.com = 193.202.110.185
Active profile: Default
PTT status: OFF
------------------------------------------------------------
2)Before pushing Poewer SW on IC-706 panel,
RRC-control (at the remote site 65km from my home)
Info
Name Value
Company Microbit
Product 1258
PID 0
Hardware 5
Software 2.50
Bootloader <= 1.7
Compiler 4.1.2 (WinARM 4/2007)
Build Dec 15 2011 15:15:54
ROM/RAM 372540/50740
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 114
Serial number 2155
MAC address 00:1e:fd:01:7f:0b
IP address 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Settings
Unit ID (Banner)
DHCP 0
IP 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 2
Control panel 1
Sip password yyyyyyyy
Sip contact xxxxxxxx.ddns.remoterig.com
Auto connect 0
Audio quality 2
Audio dual-rx 0
Codec out gain 255
Codec inp gain 18
Codec inp HPF Hz 3
Codec inp preamp 0
COM0 baudrate 19200
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 19200
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 19200
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5060
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
Continuous RTP tx 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Dynamic DNS check interval 0
Dynamic DNS host name 0
Own host name
Username
Password
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,500-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
Status
Name Value
Control panel OFF
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status OK, xxxxxxxx.ddns.remoterig.com = 112.68.223.161
Active profile: Default
PTT status: OFF
(When connected RRC-control with LAN at remote-site, DNS status was "Unkown".
After a few minites, it turned to "OK".)
At this moment, I expected the connection succeeds.
Then I pushed POWER SW on the IC-706 front panel.
After several seconds IC-706 was beeping [puuu pooo piiii ] ....[puuu pooo piiii ] ...
The AUX/MIC yellow LED on RRC-control was blinking.
IC-706 did not turned on.
---------------------------------------------------------------
3) After pushing Poewer SW on IC-706 panel,
RRC-control (at the remote site 65km from my home)
Info
Name Value
Company Microbit
Product 1258
PID 0
Hardware 5
Software 2.50
Bootloader <= 1.7
Compiler 4.1.2 (WinARM 4/2007)
Build Dec 15 2011 15:15:54
ROM/RAM 372540/50740
ETH-RAM 2944 (max 3kB!)
ResetSrc 0 [3]
Uptime 218
Serial number 2155
MAC address 00:1e:fd:01:7f:0b
IP address 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
DNS 192.168.1.1
Settings
Unit ID (Banner)
DHCP 0
IP 192.168.1.227
Netmask 255.255.255.0
Gateway 192.168.1.1
Dns server 192.168.1.1
Extern IP/Host
Eth-type 5
Web page user
Web page pwd
Program mode 2
Control panel 1
Sip password yyyyyyyy
Sip contact xxxxxxxx.ddns.remoterig.com
Auto connect 0
Audio quality 2
Audio dual-rx 0
Codec out gain 255
Codec inp gain 18
Codec inp HPF Hz 3
Codec inp preamp 0
COM0 baudrate 19200
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 0
COM1 mode 0
COM1 baudrate 19200
COM1 data bits 8
COM1 stop bits 1
COM1 parity 0
COM1 rts/cts 0
COM1 terminator (hex) 00
Use USB Com Port as COM1 0
COM2 mode 0
COM2 baudrate 19200
COM2 data bits 8
COM2 stop bits 1
COM2 parity 0
COM2 terminator (hex) 00
Use USB Com Port as COM2 0
UDP cmd port 12000
UDP audio port 11000
SIP port 5060
Web server port 80
Telnet server port 23
Rx jitter buffer size 4
Rx jitter delay 3
Audio packet size (ms) 20
Continuous RTP tx 0
Debug level 0
Disable audio tones 0
Full duplex 0
PTT-off mute delay 0
IP Type-of-Service (dec) 0
Yaesu power-on/off 0
Dynamic DNS check interval 0
Dynamic DNS host name 0
Own host name
Username
Password
Enable 0
Speed wpm [0/10-40] 0
Iambic 1
Paddle reverse 0
Weight [25-40] 30
Side tone hz [0,500-1500] 800
Side tone -db [50-0] 20
Lf delay ms [0-500] 0
Key delay ms [0-250] 0
PTT activated by Keyer 0
IN0 mode 0
OUT0 mode 0
OUT0 mode 0
OUT1 mode 0
OUT1 mode 0
OUT2 mode 0
OUT2 mode 0
USB RTS as PTT 0
USB DTR as CW 0
Enable ping watchdog 0
IP address to ping
Ping interval (seconds) 300
Startup delay (seconds) 300
Failure count to reboot 3
Status
Name Value
Control panel OFF
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status Error, failed to resolve roohegox.ddns.remoterig.com!
Active profile: Default
PTT status: OFF
I could not get connection through internet yet.
After this trial, I found that PCs on the LAN were not able to connect internet.
To recover the connection, I had to reset my router by power off.
Above is the story of my trial.
Please any idea or suggestion for this problem.
Thank you.
73
ja3aop/AKIRA
-
Akira-san,
I did some testing here to try to simulate your problem, but was unable to duplicate it. I had made the
assumptions that it had either nothing to do with the dynamic DNS address, or maybe there is a problem
with port conflict on the SIP port, which is very common for 5060 and why everyone should change this
port to something else. Neither of these duplicated the messages on your status, so I am not sure what
the cause is.
I think is is therefore related to router port forwards or something along that line. I suggest you drop me a
note directly to dj0qn (at) darc.de and I will send you a simple checklist that you can go through to make
sure that your router is configured correctly. I have helped a couple of dozen OM's get their stations working
with this list, and/or by taking over their PC's for a few minutes to find the problem. Often it is a very simple
solution, like changing the radio RRC to DHCP and assigning the internal IP number through MAC address binding
in the router instead.
73,
Mitch DJ0QN / K7DX
-
TNX, Mitch-san:
I got first connnection between IC-706mk2G and its separated pannel through internet by your help.
I set my router(Radio-site) "DMZ". And made some change on port numbers (5060 > 5061, 80 > 8000).
Then, I got the 1st success.
But I found some problems while several QSOs.
1) While QSO or watching, the radio was shut down suddenly several times.
2) While I was talking with my wife by VoIP phone, I tried to power on my IC-706 by pushing poewr SW down.
IC-706 was going to "ON" but something made shut down.
So, while pressing power SW, the radio was ON OFF ON OFF..... .
After those sudden shut down, the status of RRC control was keeping connection.
I think, there were the false signals to shut the radio down.
This is the short story of my last trials.
Thank you.
73
ja3aop/AKI
-
Hi Akira-san,
Thanks for the update. It appears that you are making progress, but may have a
network problem somewhere. It is difficult from your description to determine more
precisely where the problem lies.
I think you need some more testing, and change some of the settings to see if the
network performance improves. Try increasing the RX jitter and buffer, as well as
the audio packet size. Turn continuous RTP on, also make sure that your router has
SIP ALG turned off. Change your audio quality down to the lowest level (0) and see if
this improves the situation. Try taking things off the network and putting them back
on again to see if this really has an impact or not. We need to have you narrow this
down to figure out what the problem is.
Someone that has 706 experience like Simon may have some specific tips on configuration
that I am unaware of, in case that has an influence.
Let us know how you are doing!
73,
Mitch DJ0QN / K7DX
-
Hi Akira-San, hi Mitch,
I never have seen the 706 (I use an 706MK2 if that matters, but I don't think so) toggle power on and off.
Maybe these questions help to narrow down the problem:
1. Does the radio really power off or does the display go blank, i.e. what about the audio stream. Is it still up (check the LEDs of the RJ45 connector where the frontpanel is connected).
2. What does the status page of the RRCs show when the radio is shutting down (control panel/radio on/off)?
3. What about the Internet connection on both sides (bandwidth, reliability of connection etc.)?
vy 73
Simon, DJ4MZ
-
Hi, Mitch-san, Simon-san.
Thank you for your posting about my trial report.
1) Radio was powered off. (Radio panel was blacked out.)
LEDs of RJ45 connector was yellow. (Remoterig connection was being kept.)
So, by pressing the power SW, IC-706 waked up and the panel was lighting immediately.
Also, received signal was sounding clear.
2) The status of RRC-control after shutting was <radio=off, connction status=connected>.
3) About the Internet connection,
Control-site, 100Mbps upward and downward by FTTH(optical fiber).
Radio-site, 100Mbps upward and downward by optical fiber+VDSL.
example of tested data , up= 40.65Mbps, down= 41.57Mbps.
I intend to try again on next weekend.
Thank you.
73
ja3aop/AKIRA
-
Akira-san,
If you need any help, I can look at your setup with Teamviewer. Just remember that my time zone
is UTC+1, which means that I am 8 hours behind you. Just send me a mail directly if you need
support.
73,
Mitch DJ0QN / K7DX
-
Hi,
In past try, I put RRC-radio at my home, RRC-control at my remote radio shack, for convinience of setting up.
At last try, I changed RRC-radio and RRC-control each other. So, RRC-radio is at remote radio shack. RRC-control is at my home.
I got remote connection through internet. Then, I enjoyed some QSOs.
But, Sudden shut down were occured 4 times while 150 minutes operation duration.
The status of RRC-contorl after shut dowen is as follows:
Status
Name Value
Control panel OFF
Radio OFF
Connection status Disconnected
SIP status Idle
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5061
SIP In port 5061
Audio Out port 11000
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5061
External Audio In port 11000
External Cmd In port 12000
Other party 101.142.86.149
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status OK, roohegox.ddns.remoterig.com = 101.142.86.149
Active profile: Default
PTT status: OFF
This is my short report for my remote connection by IC-706mk2 detached panel.
Thank you.
73
ja3aop AKIRA
-
I do not think the disconnection has anything to do with the RRC.s or the ddns. it's probably a network/internet issue.
Install pingplotter www.pingplotter.com and run it against your radio-qth, then you will see if the network connection is down when you got the disconections.
73 de mike