Messages

1

General discussion forum / Kenwood TM-D710 TNC problem

« on: 2013-05-22, 18:27:20 »

Just installed my third remoterig on a TN-D710 and all basic functions work well.  However the TNC does not key the transmitter on command from the computer terminal  The terminal recognizes the TNC on boot-up but is unable to key the transmitter.  This function works perfectly when remoterig is not in the circuit. 

Any suggestions or ideas?

2

General discussion forum / Re: Two IC-7410 with remote rig

« on: 2013-02-15, 18:06:40 »

Hi Mitch,
Since we last talked, the IC-2820h is now working well with 350 feet of cat 6 cable directly between the remote head and radio using the remoterigs. 
I have an IC-7410 and would purchase another if I could accomplish the same thing with them.  The IC-7100 is not yet available here but I understand that it will not function on 40 or 80 meters which I need. If it were not for the lack of 40 and 80 the IC-7100 with the detachable control head would be ideal.

73,
Roy WA8YEP 

3

General discussion forum / Two IC-7410 with remote rig

« on: 2013-02-14, 21:47:24 »

Will two Icom IC-7410 work with Remote Rig similar to the Yaesu twin concept?

4

General discussion forum / Trouble making RRC-1258Mklls work with Icom IC-2820H

« on: 2013-01-08, 23:20:24 »

Can see and modify settings on both RCC units on LAN.
Made required cabling
Pushing power button does nothing.
Status of both units below.

Status
Name Value
Control panel ON
Radio ON
Connection status Disconnected
SIP status Unknown(1)
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.1.228
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF

Status
Name Value
Control panel ON
Radio OFF
Connection status Disconnected
SIP status Connect request
Last SIP error None
RTP/UDP audio status Disconnected
UDP cmd status Disconnected
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 12000
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.1.227
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DNS status Error, failed to resolve remoterig.com!
Active profile: Default
PTT status: OFF

5

General discussion forum / Re: Remote without internet

« on: 2012-12-28, 01:21:51 »

Mitch,
Thanks for the info.   Actually I would prefer to run a hard wire Cat 6 cable rather than wireless  I just wanted to be certain this could be done without a switch in between or that none of the wires need to be transposed from a standard patch cable.

Roy

6

General discussion forum / Re: Remote without internet

« on: 2012-12-27, 21:11:22 »

Thank You Mike.
de Roy

7

General discussion forum / Remote without internet

« on: 2012-12-27, 20:14:00 »

Question #1    Recently purchased a IC-2820H and would like to separate contol head from main unit by about 400 feet, no need for internet.  Can the Remoterig units be connected directly between the ethernet jacks with cat 6 cable?
                       If not what is the best method without using the internet?

Question #2    Is Remoterig compatible with Alinco DR-235TMKlll in any way?