Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sp2xdw

Pages: [1]
2
Name   Value
Control panel   ON
Radio   ON
Connection status   Faulty(See below)
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   Error(0)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3

I changed to 6060 but  still UDP error  --- sp2xdw@icloud.com
Dual Rx   0
Current audio packet size   20
Current audio quality   1 - Linear 12 bits 8 kHz
External IP   dwydra.dyndns.org
SIP Out port   6060
SIP In port   6060
Audio Out port   16492
Audio In port   11000
Command Out port   12000
Command In port   12000
External SIP In port   6060
External Audio In port   11000
External Cmd In port   12000

3
Dear,
Mitch DJ0QN / K7DX
 I have the same problem. For some time, only occasionally reaches connectivity . Most of the time a message is displayed below: UDP cmd status   Error(0)

Name   Value
Control panel   ON
Radio   ON
Connection status   Faulty(See below)
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   Error(0)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
Current audio packet size   20
Current audio quality   1 - Linear 12 bits 8 kHz
External IP   dwydra.dyndns.org
SIP Out port   5060
SIP In port   5060
Audio Out port   20004
Audio In port   11000
Command Out port   12000
Command In port   12000
External SIP In port   5060
External Audio In port   11000
External Cmd In port   12000
Other party   83.8.145.90
Input 0   High
Input 1   High
Input 2   High
Output 0   High
Output 1   Low
Output 2   Low
DNS status   OK, dwydra.dyndns.org = 83.8.145.90
Active profile:   Profile 1
PTT status:   OFF

4
General discussion forum / Re: Help configuring Serial Port
« on: 2014-05-11, 01:20:32 »
Ero http://qrz.com/db/IK1DYS. Purtroppo, questo sistema non mi piace. Alla ricerca di "Y" Cavo per Ultrabeam come antenna SteppIR collegamento SteppIR-TS-480-PC. Il mio attuale sistema di controllo remoto "Remoterig" consente di chiamare: 1 rotore 2 TS-480 port "CAT" Kenwood steer Ultrabeam.
Sto cercando una soluzione del genere che solo "Remoterig" controllare il rotore 1, 2 e 3 UltraBeam TS-480 da HDRLog. Sto contando sul vostro aiuto.

I am looking for equivalent Y-cable (this is for SteppIR) through which I can control remotely via a program HDRLog Kenwood TS-480 and at the same time the CAT port control antenna Ultrabeam. Unfortynatelly Remoterig has only 2 serial ports. One of them allows me to control the rotor. Second I can use to control radio or Ultrabeam.

5
General discussion forum / Re: Ultrabeam remote control
« on: 2014-04-09, 00:24:14 »
I use CAT to control the Ultrabeam @  RRC-1258MkIIs to control the Kenwood TS-480.

Pages: [1]