Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - Mitch

Pages: [1] 2
General discussion forum / Audio Problems
« on: 2019-07-13, 20:45:16 »
Can anyone tell me if there is a fix for no audio from the Kenwood 480 Sat, this morning the audio would not work for some reason. This turns on OK and also receive fine.

Have placed new power cable's, also factory reset, changed over to second face from car, second RRC unused control connected also show the same problem also.

73 Gary

General discussion forum / Install WiFi Pins
« on: 2019-06-23, 16:48:42 »
Hello there can anyone help me out i am trying to install Pinheader for WiFi card in one of my first RRC Control box.

Looking at my second box it looks like a newer build inside. The newer box looks like needs more pins installed rather than old one.

Can anyone give me some advice in how this show be in the older version with 10 pin holes rather than my second RRC Control with 14 pins.

73s Gary

General discussion forum / Losing connection
« on: 2019-06-09, 01:39:20 »
Hi there can anyone help me out, for some reason each time i key the microphone the red light flashes and shows like the microphone is pressed on the Kenwood 480 Sat.

All the jumpers on both boxes have not been changed in any way.  I have tried two different power supplies to each boxes and also 3 different microphones with no joy.

Any help would be greatful


General discussion forum / Rotator advice
« on: 2019-04-19, 03:17:38 »
Would anyone know if this small light duty Yaesu G 450C Rotator would be OK to control the 1.5 meter 3 el Yagi or would i need to go for stronger for the lightweight Yagi

Many Thanks

General discussion forum / RTL-SDR V3
« on: 2019-04-15, 10:02:08 »
Hello there would anyone know if possible to work both RRC-1258MkIIs and Kenwood TS 480 to RTL-SDR V3 RTL2832U. The cable has been already installed inside radio to RTL-SDR before but now would like to work with remoterig.

If this is possible to do on COM 1 both boxes how would I have settings in Serial settings in both Radio and Control side and is there anymore changes needed in settings.

Many Thanks

General discussion forum / Lose connection with radio side
« on: 2018-10-01, 05:36:17 »
Can anyone help me out i always seem to lose the connection with RRC Radio side and have to ask my friend to turn off and on again for control to find TS 480 Sat.

General / RRC Kenwood Nano "license expired"
« on: 2018-08-14, 02:40:20 »
Hi there,

can anyone tell me is it possible to renew the Kenwood trial period, never got chance to work this here when Remote Rig was not working for over six months.

Message says trial period stopped by the expire. Can you tell me if this is possible to be fixed with Lic.ID 6d98 or would i have to try install fresh again.

73 de Gary

Hi there,

Can anyone tell me i have two kenwood 480 Sat's. Old one works fine with remoterig ok.  Tied to change to other second 480 Sat but like getting a carrier when i work radio on USB.

Seen a old post before there is two versions of kenwoods SAT & HX that you have to configure the red pins in RRC Control and RRC Radio depending on sernial numbers on version of Sat or Hx.

Would like to add the Kenwood 480 Sat i work from the remote station placed in my works van and nicer looking radio to my home. Any help would be greatful..


General discussion forum / TS-480 and HRD
« on: 2018-04-08, 02:16:09 »
Hi there,

Can anyone help me out i would like to connect both the RRC Radio side and the RRC Control using Ham Radio Delux,  Would anyone know how i can set the COM ports on each box and would i have to change settings in HRD, both RRC and Kenwood 480

73 Gary

General discussion forum / RRC-1258MkIIs Feedback Problems
« on: 2018-01-31, 22:41:14 »
Hello there.

Can anyone help me out, i am having problems when i key the Microphone on Kenwood 480 Sat, i have been told there is feedback from my audio with the RRC-1258MkIIs boxes.

The radio works fine without Remoterig so not sure if it could be the way the jumpers and red cables are configured in both boxes. Could anyone tell me is there i link that i can look at the way control and radio should be installed inside.


General discussion forum / Control Side Cable W2IHY
« on: 2017-10-10, 21:57:08 »
Hello there,

Can anyone help me out with any information on a cable from W2IHY’s 8-band EQplus, W2IHY 8 Band Audio Equalizer to remoterig at the (CONTROL SIDE) And this would fine at the Radio side



General discussion forum / IMO Mobile WiFi device
« on: 2017-08-14, 00:28:54 »
Hello there,

can anyone help me out and tell me if I get a IMO WiFi device like and connect to Radio and the antenna side of Kenwood 480.

I have been told that it is a dynamic IP address would it then possible that I can then forward the ports as normal and use the radio over the internet to the control side.

Many Thanks

Hello there can anyone tell me the best way to set both remote boxes so I don't need to use the Ethernet cable.   I have both the WiFi antennas from the shop but just not sure if there is a link to configure this.

Best 73's

General discussion forum / 300 Point Check List
« on: 2015-11-21, 05:37:50 »
Hello all,

Not sure if this is the correct place to post this topic but can anyone out there help me out.

I have lost the 300 Point Check List & looking for anyone that can PM me it once again.

Best 73s

General discussion forum / Working Remoterig Mobile
« on: 2015-08-13, 12:32:45 »
Hi there,

Can anyone tell me I have Remoterig setup at my flat and works great. I but would like to know how I could set up Remoterig from Kenwood 480 in the car with a Dongle to laptop.

Has anyone done this before, I have seen many videos of Remoterig stations working in hotels with routers but none yet that I can find when working mobile station.


Pages: [1] 2