Messages

1

Configuration, Webswitch 1216H / Two webswitch units combined with one LAN

« on: 2021-07-04, 19:11:55 »

Hi,
I have seen an application for that but cannot find it again. 1216H.
73,  Thomas

2

General discussion forum / Re: Two webswitches possible on same remote location ?

« on: 2016-03-27, 22:48:47 »

thank you Mitch. I have tried this, maybe the port number I tried was occupied.
73,  Thomas DL7AV

3

General discussion forum / Two webswitches possible on same remote location ?

« on: 2016-03-27, 13:37:26 »

Hi,  two webswitches possible on same remote location to be able to use 10 relays?

4

General discussion forum / Re: no temperature readout

« on: 2013-10-30, 22:08:43 »

thank you Jan. Deleting and rescanning was the solution. I just did not imagine that I had to delete something!!
regards,  Thomas

5

General discussion forum / Re: no temperature readout

« on: 2013-10-28, 17:58:12 »

Hi Jan,

sorry I did not find a Manual for the Webswitch, so I don't know what you mean by scanning the sensor!? It is the only sensor and the polarity is OK.

regards,  Thomas

6

General discussion forum / no temperature readout

« on: 2013-10-28, 11:38:46 »

Hi,
this is probably easy to answer. I get no correct temperature readout:
Current Temp A(IN): Current 0.0625, Max 0.0625 , Min 0.0625
sw 3.3
Build Jun 12 3013
What to do?
regards,
Thomas  DL7AV

7

General discussion forum / Re: JT65 via Remoterig?

« on: 2013-08-15, 15:46:37 »

Hi John,

thank you! That's very important news for me, saves me time.

73,  Thomas  DL7AV

8

General discussion forum / JT65 via Remoterig?

« on: 2013-08-10, 08:44:42 »

Hi all,
before I try it: Has anyone used Remoterig for the reception of weak signals via JT65? What settings did you use to receive signals below the noise level? "0-alaw 8 kHz" will probably not work, maybe "linear 16bits 8 kHz"?
 
73,  Thomas  DL7AV

9

General discussion forum / Re: Using Remote Rig to turn on/off 12v coax relay?

« on: 2013-05-25, 16:44:18 »

Paul,
do I understand correctly that your solution cannot be used if you already use the IO ports for CW keyer plus paddle?

73,  Thomas  DL7AV

10

General discussion forum / Re: Elecraft K3===>>> lightning protection

« on: 2013-05-25, 16:40:05 »

Hi Staffan,
my compliments for your web controlled Antenna Connection system. Lightning energy is prevented to get into the shack through the coaxial shield. I have not seen that before. You seem to use special N-connectors with no lock nut.

73,  Thomas  DL7AV

11

Configuration, RRC 1258 / Re: how to delete profiles?

« on: 2012-02-04, 18:26:30 »

Thank you Jan, good service!
But "Remember to "Submit"" has to be moved to 3/
Works fine now.
73,  Thomas

12

Configuration, RRC 1258 / Re: how to delete profiles?

« on: 2012-02-04, 12:34:04 »

"So "blocked" means the profile you change to has the wrong IP settings for the network the RRC is in?" YES
This is the exact info:

profile: “default”, good connection
IP address 192.168.178.29
Netmask   255.255.255.0
Gateway   192.168.178.1
DNS   192.168.178.1

profile: “dl7av”, must be changed or deleted, wrong network settings. By Setup Manager:
IP address: 192.168.0.29
Netmask   : 255.255.255.0
Gateway   : 192.168.0.30
DNS       : 0.0.0.0

13

Configuration, RRC 1258 / Re: how to delete profiles?

« on: 2012-02-03, 18:37:59 »

Thank you Jan. But there may be a misunderstanding. As you said I changed from default profile to the profile that does not give me access, but did not submit. Then I changed my password in the IP settings and applied. Same result, the profile does not work because it is looking for a wrong network (as I can see in the “Net info” in the setup manager). Any way to change the settings of the profiles which look for a different network? Factory reset??
73,  Thomas DL7AV

14

Configuration, RRC 1258 / how to delete profiles?

« on: 2012-02-03, 12:56:43 »

I now have 3 useless profiles due to playing around with the settings at different locations. When choosing one of those the access is blocked and I have to use the setup manager via USB to get to the default profile. How to delete profiles? And how to rename them?
73,  Thomas  DL7AV

15

General discussion forum / Re: 3G via ICS (notebook and HSPA stick)

« on: 2011-12-22, 18:10:31 »

Thank you. Jan, is the beep (after pressing the start button at the TS-480) an indication that the setup is basically ok? No way to get a display or audio by different ways of pressing the button. - I wanted to bridge the two connections at first. But Windows XP says I can only bridge two LAN or high speed internet connections, the USB 3G modem is different. For the time being I have given up. Thanks and good luck for further developments with the wonderful Remoterig. 73
Thomas DL7AV