Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - IZ7ANL

Pages: [1] 2 3 4
1
General discussion / Re: Com issue RRC Micro
« on: 2014-12-29, 17:25:48 »
Roland,
I'd the same problem and I decise to use ver. 12 it's more stable
My setup TS480 Radio Control Program for 480
My best wishes for 2015
73 Nick

2
I have installed ARCP-480 and after that, all it's working,  HRD also . !!!!
73 Nick

3
Many thanks Franco, I'm using Ham Radio Delux and I have the same problem on 2 PC...
I'll try again
Ciao Nicola

4
Any one try new firmware?
I use: OS XP SP3, TS 480
I can  change all the set (slide control, Pre, Att, ecc) at exception of the frequency! It seems to change after 1 sec came back at preview.
I tried on 2 different computer(OS XP SP3), same problem
Any suggestion?
My best regard IZ7ANL

5
In my case, setting TS480 FW2.65, all works OK
73 IZ7ANL Nicola

6
General discussion forum / Re: Expert 2K-FA
« on: 2012-08-03, 20:15:43 »
Many thanks Wilston I'll wait your test.
My best regard Nicola

7
General discussion / Re: Problems Firmware 1.5.3 & 1.5.4
« on: 2012-06-10, 10:03:33 »
Dear Roland,
do you have any news?
my best regard
Nick

8
General discussion / Problems Firmware 1.5.3 & 1.5.4
« on: 2012-05-28, 23:43:15 »
Dears,
with firmware 1.5.3 & 1.5.4 I can't connect sometimes TS480 and Prosistel rotor.
All it's ok with 1.5.2!
I am using windows XP professional service pack 3
Any suggestion?
My best regard
Nicola MILILLO

9
General discussion / Re: HamRadioDeluxe performances
« on: 2012-01-30, 18:58:22 »
Hi Enrico,
I'm using micro PC since last november and I have the same equipment that you use, only one difference, HRD run on XP, I never had any problem all seems work ok.
My best regard
Nicola
 

10
General discussion / Re: Com1 & Com2 sometime
« on: 2011-12-26, 20:31:24 »
Daniel,
I'm also happy for you, I have solved any problem with new firmware 1.4.0, anyway I would like to suggest you to set  rts/cts in "no" position otherwise when you use PC client the indication of bearing could be not stable.
My best regards and happy new year 2012.
'73 IZ7ANL Nicola

11
General discussion / Re: Com1 & Com2 sometime
« on: 2011-12-23, 09:55:57 »
Ronald,
many thanks for new firmware 1.4.0, I solve any problems,  now all work fine.
My best Christmas wishes for you and your staff.
'73 Nicola MILILLO

12
General discussion / Re: Com1 & Com2 sometime
« on: 2011-12-22, 00:35:41 »
Mike,
may be you read last post and you miss understud my problem.
I am using at home RCC units, on COM1 I have connect Prosistel D rotor and all work fine (so this means that set an cable are ok), BUT When I using PC client I cant contro a rotator on Com1.
Please look my pictures on previw post so you can have a better idea what I mean.
I follow a Ronald istractions but no way.
The only difference are: RTX and Com, in my case I use Com1 like a rotor control and com2 to control TS480, in Ronald case he uses RTX 706 on Com0 and rotor control on Com1. 
'73 Nicola

13
General discussion / Re: Com1 & Com2 sometime
« on: 2011-12-21, 20:06:45 »
Roland,
thank you for your attention, I follow your istractions however your setting are the same setting that I used like you can see in my previw post (look my pictures).
The only difference between your setting and mine, you use Com0 with IC706 and Com1, in my case I use Com2 with TS480 and Com1.
May be this is the reason becouse my PC client don't work Com1 with rotor.
I will wait an PC client upgrade firmware.
My best '73 Nicola

14
General discussion / Re: Com1 & Com2 sometime
« on: 2011-12-20, 21:54:19 »
May someone help me to discovery what is wrong in my setting?
'73 Nicola

15
General discussion forum / Re: Expert 2K-FA
« on: 2011-12-19, 17:28:21 »
Guy,
15 days ago I have been in Rome  to viset SPE Laboratory and I asked if it was possible to pick up the TTL signal or serial signal befoure the USB converter but they didn't have more time, may be in future.
I serch in web and I found a lot of USB server converter (stand alone) but I didn't know the resalt, now your reporte convice me to wait.
I am studing to add a serial control at mine tube homebrew amplifier (2 x 4-800)
Have you look my PC client post? any suggestions?
My best regard '73 Nicola

Pages: [1] 2 3 4