Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - N9RC

Pages: [1]
1
Android App / 1216H Android app pulse output problem
« on: 2016-08-13, 19:51:10 »
I have two 1216H output modules.  I am using android app for backup.  1216H with hardware version 2 works with pulse outputs.  Second unit with hardware version 3 does not.  I have tried firmware 4.20 and 4.23.  Pulse works in both from web app.  Direct contact on/off works in android app.

2
I am now OK.  In testing I had just booted and it took 5 minutes to detect missing ping.  I wrongly assumed that was wait period for first failure.

Thanks,  N9RC

3
Configuration, Webswitch 1216H / Faster missing Ping action
« on: 2016-07-30, 02:31:51 »
The configuration for "Ping action delay" does not allow times less than 300 seconds.  Is there a way to enter a smaller delay?

4
OK...

I am sorry I did the setup six months ago and may not remember the sequence correctly but I now see user name and password in the IP settings in the LAN setup access. 

All is well.  Thanks.

5
There was a way I used to access the 1216H application "directly" with the USB port and the web application was run.  This is how I originally entered user name and password.  There must have been software I used at the time that I no longer have or I am not seeing this feature in setup.

6
Yes, that is the pull down. 

Not sure what is going on with the router, but it works fine now.  I can access through the local LAN via setup OK also. 

Should I be able to access the application through USB only?

Thanks for the help.

7
LAN OK now.   I checked DHCP on setup tab.  My LAN IP changed and it works OK.  Still no USB application connect?

8
All the setup functions work and appears to "see" the device on the network.  I am not sure that I need the serial port tab or a virtual address.  My concern was the physical port does not appear n the pull down window. My problem is that I cannot get into the application piece in USB or on local LAN.  I had this all working back in May.  The device was configured then with user and password etc. and worked OK with internet access.  It has been sitting since then.  I have tried different versions of firmware and setup and trieda Windows 7 computer. 

9
I am running v 1.28 Setup.  I can upload firmware and setup IP.  Setup does not allow setting correct serial port in W7 or W10.  I cannot access the detail 1216 operating info via USB.

10
Configuration, Webswitch 1216H / Webswitch 1216H LAN access
« on: 2015-12-04, 07:56:23 »
I had the 1216H running fine 6 months ago.  I have reactivated the project after a disc crash with a new router and Windows 10.  Setup seems to run OK.  I uploaded firmware 4.23 and configured the new router port and address.  Ethernet light is blinking on 1216 and router sees 10 MB connection but no identification info.  I also do not see the 1216 on W10 network and cannot access the 1216 through its local network address(or through internet.)  As a side note it seems like there was a program to access via USB. Is this still available?  The configure serial window in setup does not have correct comm ports available. 

11
Problem solved.  I changed my internet modem to a "bridge" type.  Configuration is easy now. :>)

12
I am now focused on my Westell 6100 DSL modem.  It apparently is combination modem and basic router with port forwarding control.  I believe my outside access is being stopped there.  Will be talking to my ISP.  Has anyone had similar issue?

13
DMZ same result.  I will try a different router later today.  For failed test I used "find ip" to find  my public IP address.  Added colon 85 for port and entered in browser.  I have tripled checked setup.    I assume I don't have to use ddns for addressing?

14
I switched to port 85.  Same result.  OK local LAN, no connection through router.  I am typing in my public IP address.
50.X.XXX.XXX:85 and that always times out.  If I type 192.168.1.236:85 OK

15
I have a new Webswitch 1216H  configuration 192.168.1.236 port 80.  It operates fine on local LAN.  I have a Netgear N600 router configured for port 80 pass through to the 1216H address.  I have been trying to use my public IP address to access(It has been static).  All I get get is time outs.  I am trying to access from W7 Firefox browser on local LAN.  I have also tried remote through Android Gingerbread phone same result.  Any ideas?

Pages: [1]