Messages

1

General discussion forum / Re: Issues when updating the RRC's Firmware using USB

« on: 2011-03-26, 03:04:14 »

I ran into the same problem when using the USB cable.  I used the network connect method and the update was successful.

Here is the information returned when I ran the program you supplied. Hope this helps.  Thanks for the great support and continued improvement of this great product.

73's  Bob KA4JXT

Microbit USB info v1.0:
USB:[Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8]
USB:[Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9]
USB:[Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA]
USB:[Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB]
USB:[Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC]
USB:[USB Root Hub]
USB:[USB Root Hub]
USB:[USB Root Hub]
USB:[USB Root Hub]
USB:[USB Root Hub]
USB:[USB Composite Device]

2

General discussion forum / Re: TS-B2000 + RRC-1258 MkII-Set + RC-2000 = Works?

« on: 2010-12-17, 04:36:33 »

I run the B2000 with the RC2000 and it works perfectly.  I am completely satisfied and enjoy full remote control.  The only drawback  would be if you want to operate from the station location as well as remote.  In that case the TS2000 with the front panel would be best.  In that configuration you should have both local control using the front panel and remote control using the RC2000 with the RRC-1258 MkII.  I have m yB2000 dedicated to remote operation so it is not a concern for me.  I have other HF rigs I prefer to operate when I am in my shack.

3

General discussion forum / Re: Remote access behind NAT firewall

« on: 2010-06-13, 02:46:53 »

Mike,

Thanks for the response.  I have everything set up and it is all working properly over the internet but from some locations I can not connect.  I will change the SIP port on both ends just in case the hotel is using 5060 or blocking it for some reason.

Thanks,
Bob

4

General discussion forum / Remote access behind NAT firewall

« on: 2010-06-09, 03:30:20 »

Let me restate my earlier post because I have had no suggestions. 

QUESTION:  Is it possbile to connect over the internet to my TS-2000 if the remote internet access using the RC-2000 is behind a NAT firewall?  Everything works perfectly when connected directly to the internet but not when connected to the internet through a NAT firewall on the remote end. 

Thanks. 

Bob

5

General discussion forum / TS-2000 remote connection question

« on: 2010-05-29, 23:18:45 »

First let me say I am absolutely delighted with this wonderful equipment. 

Here's my question:  Everything works fine on my local network.  Everything works fine when connecting from other friend's homes over the internet.  I connected at a hotel while traveling by using a wireless bridge and a router/switch.  I used the bridge to access the wireless internet in the hotel.  The output of the bridge became the WAN input for the router/switch.  I cloned the laptop's MAC address in the router and connected my laptop to one of the ports to bring up the hotel's splash page.  I entered the hotel provided  accesss code and accessed the net without problem.  I then connected the RRC 1258 MkII to another port on my router/switch and everything worked perfectly. 

On another trip to different hotel I used the exact same configuration (bridge and routher/switch) but this time when I pressed the power button on the RC2000 I got receive audio coming back to me through the speaker but no display and no control over anything.  The only way to turn it off was to disconnect the power.   The only difference was the internet service provider/LAN difference between hotel A and hotel B. 

Does anyone have any suggestions how to overcome the issue at hotel B?  I plan on taking this remote on many business trips and would like for it to work constantly rather than not know until after I check in. 

Thanks for any suggestions. Bob