Messages

1

Configuration of Routers, Firewalls, etc / Re: icom ic 7100 problem after change adsl

« on: 2017-07-06, 13:46:19 »

Thanks Mitch,
probably the router you checked out is the original one... mine is customized by the operator, attached you can see a snapshot

any way to use a EoIP (ethernet over IP) by using two mikrotik routers? https://mikrotik.com/testdocs/ros/3.0/vpn/eoip.php

2

Configuration of Routers, Firewalls, etc / Re: icom ic 7100 problem after change adsl

« on: 2017-07-06, 13:10:31 »

thanks Mich,
unfortunately there is no way to found something about SIP ALG... besides the firewall seems cannot be disable.. only security level "high" "medium" "low" (of course mine is already LOW)

the modem router is a Technicolor TG789vac v2: this is a customized modem/router and I cannot change it since the telephony part is embedded (voip) and not manageable by end user

73 Andrea.

3

Configuration of Routers, Firewalls, etc / Re: icom ic 7100 problem after change adsl

« on: 2017-07-06, 11:46:54 »

Hi,
I'm having the same problem here.
I switched from a WISP connection (with IP static address) to a FTTC connection at radio side.
I can't connect anymore the radio, same error at control side: connection status faulty, connected transfering, RTP/UDP audio status: Stalled
At radio side seems OK (OK, connected/transferring).

The FTTC ISP declares that all ports are reachable, I have a dynamic public IP address, the remoterig ddns works well.
The web interface of radio side is working on port 81 and is reachable with no problem (of course I forwarded port 81 to radio control).
I tried to change ports, from 13000-13002 to 13003-13005 and then 65532-65534 but nothing changed (of course I changed and I opened the port on radio FTTC router).

Any idea? by my side no...

The only possible solution that pops out in my mind is to setup a PPTP Router to Router secure tunnel (something like this https://mikrotik.com/testdocs/ros/3.0/vpn/pptp.php ) in order to use same radio side ip class at control side

thanks in advance

73 Andrea IK1MVX

4

General discussion forum / Re: Antenna Switch Information Needed

« on: 2016-06-07, 12:14:06 »

Hi,
I'm using an ameritron RCS-4 and I'd like to switch antenna by remote by using webswitch relays.
Do you foresee any problem by leaving the relay ON (=closed) for a long period (days)??

thanks, 73
Andrea IK1MVX

5

General discussion forum / Yaesu FT-DX1200

« on: 2016-03-21, 13:53:17 »

Hi,
anyone is using FtDx1200 with rrc-1258 and HRD?? (or with any other program) Does someone is using PSK31 and/or JT65?

What are the settings to be used? 3 or 4?

thanks in advance

73, Andrea IK1MVX | KC2ZDR

6

General discussion forum / Icom ID-880H

« on: 2010-11-03, 17:38:34 »

Hi!
What about Icom ID-880H?
It seems a radio coming from "IC-2820 experience": is it possible to use RRC togheter with this rig?

73, Andrea - IK1MVX / KC2ZDR

7

Allmänt diskussionsforum / Re: Non-HF Rigs with remote front panels?

« on: 2010-11-03, 14:48:07 »

Hi,
similar to K9GVF, I would like to connect a Kenwood TM-741 (or TM-742) via internet by using RemoteRig.
I have no requirement about remote front panel: the rig could remain as is and the remote station can use a PC in order to control the TM-741. Is it feasible?
Is it possible to control up to 3 rig (for instance, 3 Kenwood TM-741) by using the same ADSL connection? (It is a 8Mbit downlink / 1Mbit uplink connection dedicated to this purpose).

Last question: Is it possible to control 3 ICOM IC-2820 by using the same ADSL connection? 

thanks in advance!

Regards,
Andrea, IK1MVX / KC2ZDR