Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DF1NP

Pages: [1] 2 3
1
Feature Requests / Re: External key / external Elbug
« on: 2017-05-10, 19:08:22 »
Hi Roland,

I use ETM 9c keyer.
Conf. and wireing look manual 1258 MK-II cw-keying: I/0 Connector control and radio RRC.

73
Willi

2
Hi Per,

Congratulation! Happy to hear all is working now.  :)

73
Willi

3
Hi Per,

My conf. for profil CAD:

Serial settings control:

COM1 mode  Mode-7, CAT to COM2 (remote)
COM1 baudrate 9600   
COM1 8   
COM1 stop bits 1
COM1 parity 0 - Off
COM1 rts/cts  Yes   
COM1 terminator (hex)  00
Use USB Com Port as COM1 No 
   
COM2 mode Mode-4, Kenwood, Yaesu, Elecraft   
COM2 baudrate  9600   
COM2 data bits  8   
COM2 stop bits 1   
COM2 parity 0 - Off   
COM2 terminator (hex) 
Use USB Com Port as COM2  Yes   
   
COM3(Extra) mode (USB-COMFSK) Inactive

Radio:
Serial settings

COM1 mode  Mode-7 CAT to COM 2
COM1 baudrate  9600   
COM1 data bits 8   
COM1 stop bits 1   
COM1 parity 0 - off   
COM1 rts/cts  Yes   
COM1 terminator (hex) 
   
COM2 mode  Mode-4, Kenwood, Yaesu, Elecraft   
COM2 baudrate 9600   
COM2 data bits  8   
COM2 stop bits 1   
COM2 parity 0 - Off   
COM2 terminator (hex) 

Radio autoconnect: yes

For ARCP-590 you first must install the virtual comport drivers.

good luck
Willi

4
Hi Per,

Normaly I am using TS-590 TWIN (very  comfortable). But I also can work by CAD. So the settings for HRD  is: Kenwood, TS-590, COM (look at your device manager), speed 9.600, no: CTS, DTR, RTS.

Using ARCP is a little bit tricky, hi. Speed 9.600, comport as above.

I prefer working with USB cable: seriel setting: USB comport as COM 2: yes

73
Willi


5
Hi Per,

For configuration look at RRC 1258-MKII user manual, page Kenwood general.
http://www.remoterig.com/downloads/RemoteRig_RRC1258-MkII_Users_manual.pdf

You also can use ARCP-590 vers. 2.02 freeware program by kenwood. http://www.kenwood.com/i/products/info/amateur/ts_590/arcp590_e.html

73
Willi

6
Configuration, RRC 1258 / Re: TS-590 Twin I/O Settings
« on: 2017-04-25, 13:46:35 »
Hi, Robert,

Here my I/O conf.:

IO settings control:

IN0 mode keyer   
OUT0 mode  keyer   
OUT1 mode  keyer   
OUT2 mode  keyer   
USB RTS as PTT disabled   
USB DTR as CW disabled

IO settings radio:

OUT0 mode I/O keyer 
OUT0 on/off     
OUT1 mode I/O keyer
OUT1 on/off     
OUT2 mode I/O keyer 
OUT2 on/off 
     
3,5mm stereo cable from radio pad out to key TS-590 radioside.
Look at manual RRC-1258 MKII: keyer

73
Willi
   



7
General discussion forum / Re: RC 2000 - 0,1KHz step
« on: 2015-12-29, 14:28:03 »
Hi Simon,

I send you some photos from my mechanical and electric solution with HEDS-5640

73
Willi

8
Configuration, RRC 1258 / Re: Ts2000+RC2000+PC on Radio Site
« on: 2015-12-14, 22:28:39 »
Hi,

For my TS-2000 / RC-2000 equipment I am have this configuration:

Control Settings:
Radio:
Program Mode: 8 TS-2000
COM 0 Baud: 57600

Serial:
COM 1: inactive
COM 2: Mode 4
Baudrate 9600
Use USB: yes

Radio settings (remote):
Radio:
Program Mode 8 - TS-2000
COM0 Baudrate 57600 

Serial:
COM 1: inactive
COM 2: Mode 4
Bauderate 9600

Cable at control: USB from RRC to PC + TTL from RRC to RC-2000
Cable at Radio: RS-232 from RRC COM 2 to RS-232 TS-2000 + TTL from RRC to TS-2000
My cad program: ARCP-2000 or if you like: HRD

So you can use RC-2000 and CAD at the same time.

73
Willi

 
     


9
Hi,
 
Long time I also used IC-7600. Software was N4PY (http://www.n4py.com/) and vfo was woodbox tmate2 (http://www.woodboxradio.com/tmate2.html).

73
Willi

10
General discussion forum / Re: TS590 & 590SG twin
« on: 2015-06-19, 13:12:04 »
Hi,

I am using 2x TS-590S with upgraded software to Vers. 2.0. So the most features are the same as TS-590SG and I think, if you want, you can combine the new and old one. But it is necessary? TS-590SG is not much better, hi.

73
Willi

11
Configuration, RRC 1258 / Re: TS590S Twin
« on: 2015-04-27, 17:56:24 »
Hi,

Sri, I have no VGS-1

73

12
Configuration, RRC 1258 / Re: TS590S Twin
« on: 2015-04-13, 10:55:54 »
Congrats    :)

73
Willi

13
Configuration, RRC 1258 / Re: TS590S Twin
« on: 2015-04-11, 14:23:28 »
Hi,

Mike has to go through RRC, not to TS-590. Check the cables: http://www.remoterig.com/schema/K19-20-TS-590-twin.pdf

Keyer cable goes from pad Radio RRC to key (not paddle) TS-590. Use Vox for CW at TS-590.  See manual RRC: keyer
Sri, yes Baudrate in menu is 61.

73
Willi

14
Configuration, RRC 1258 / Re: TS590S Twin
« on: 2015-04-03, 22:03:25 »
Hi,

Change the baudrates (Kenwood Menue 56 and RRC 1258) to 9600. Radio-Mode 18. COM 2 mode is logical parallel to com 0.

73
DF1NP

15
General discussion forum / Re: TS-590 TWIN
« on: 2015-02-18, 18:37:26 »
Hi,

I upgraded my both TS-590S to vers. 2.0 succesfully. It is still working.

Pages: [1] 2 3