Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - cx6vm

Pages: [1]
1
Hello

today i noticed that my K3/0 mini is not transmitting on any mode, SSB, CW, FT8

Radio go on TX, but no RF output

I can receive without problem on SSB, CW and also FT8, but incredible that I cannot transmmit

Any idea what to check?, MIC gain is OK, POWER is OK

thanks
Jorge
CX6VM/CW5W


2
Konfiguration av RRC 1258 / RRC1258, K3/0 mini no SSB output
« on: 2023-10-10, 02:52:50 »
Hello

My setup with K3/0Mini and remoterig boxes was working fine

Now after some months not doing a phone qso, I tried again but no audio out. I am usinh MH2 microphone with the K3/0 mini. I can see my amplifier client showing 1200 watts, but no ALC bars on K3 display, I was monitoring me but not listening my voice.

I had some storaged messages on K3īs M1, M2, M3 and M4 memories and the work OK, perfect output audio showing ALC bars on my K3 display

Any idea what may I check?

thanks!

Jorge
CX6VM

3
Konfiguration av RRC 1258 / IP setup problem
« on: 2023-07-18, 19:19:04 »
Hello

I know this was discusses many times, but I couldnīt figure out who to solve it.

I have K3/0 Mini and remoterig boxes working perfectly on the SAME network

My internet link to the station broken, so I installed another internet system at the station

So now I have diferent networks on both sides

I have a dyndns service, I setup it on the remote router and I add it on my local remoterig settings (192.168.0.169)

Sometimes it worked, but now is not working, so i think is this IP changing but I couldnīt figure out how to have it working

I apreciate any help to set up it

thanks in advance!

73,
Jorge
CX6VM/CW5W

4
hello

I change my remote internet provider with Movistar Amper 2000 4L router like this one https://www.robustel.com/en/product/r2000-vpn-gateway/

I do all the configuration but couldnīt find where to setup DDNS to access it from other network. Movistar support on my country didnnīt give a solution yet, so I want to know if someone can help me to tell me where to register my tplinkdns on this router

thanks in advance!

73,
Jorge
CX6VM/CW5W

5
General discussion forum / TURN ON K3/0 Mini REMOTELY
« on: 2019-09-05, 23:05:27 »
HELLO

I want to know if itīs possible to turn on remotely, maybe through local remoterig box, the radio that I use for control side, Elecraft K3/0 Mini

I will travel, but I donīt want to carry my control side equipements (K3/0 Mini, remoterig, paddles, Mic), so thinking that if I can turn on my K3/0 Miini, I can do CW with N1MM+, using TeamViewer to access my control site laptop.

I donīt want to keep the radios ON for a week, so I need to turn on it anyway

thanks!
Jorge
CX6VM/CW5W

6
General discussion forum / buying WiFi interface
« on: 2019-05-07, 00:09:32 »
Hello

where I can buy the Wifi Interface in USA?  Elecraft donīt list it on the website

My RRC1258 have serial number 4200, dont know if it has P3 in place to make the WiFi interface installation easy, can you know that from the serial number?

thanks!

73,
Jorge
CX6VM/CW5W




7
Hello

still trying to setup FT8 to work.

If anyone is using a pair of K3/100 radios, remoterig and a soundcard, and can help me, I appreciate it very much

I can receive on FT8, but couldn't transmit

So I need to know, what cables are you using from RRC control and soundcard, where are they connected, etc, etc, etc

thanks in advance!

73,
Jorge
CX6VM/CW5W

8
hello

I have my remote station with two K3/100 and remoterig boxes working OK for CW and SSB

For SSB I use Elecraft MH2 microphone connected to AUX/MIC connector on front of RRC control

What about FT8?

I can receive, but when on transmitt, radio go to TX, but nof RF out.

I made a cable, RJ45 on one end to connect to AUX/MIC connector on front of RRC control and on the other end 8-pin DIN female that fir on MIC on the front of K3/100 on the control side.

I have a Heil adapter (red cable), in case I can try it, but need to know how

thanks for the help!

73,
Jorge
CX6VM/CW5W

9
General discussion forum / Ethernet Speed
« on: 2018-12-23, 01:58:26 »
Hello

I have a new switch, with leds that indicate the connection speed. 10 Mb, 100 Mb or Gb

Remoterig connection, is on 10 Mb range, thatīs OK?  Or thereīs something to upgrade to have it fast?

thanks

Jorge
CX6VM/CW5W

10
Hardware, Cabling, Installations / K3 footswitch
« on: 2018-11-17, 01:40:36 »
hello

I have remoterig working properly with two K3/100 on both ends

Today I connected a footswitch to PTT IN on the back of K3/100, but no PTT, radio doesnīt go to TX

What else may I need to check to use footswitch?

thanks,
Jorge
CX6VM/CW5W

11
Hello

is any way to receive the new posts and replies to my own posts on my email?

I am going frecuently to the post website to see if I receive any answer, I think will be a way to setup email forwarding, but couldnt find it

thanks in advance

73,
Jorge
CX6VM/CW5W

12
Configuration, RRC 1258 / new setup 2 x K3/100 not working
« on: 2017-11-16, 17:01:37 »
Hello

I couldnt setup remoterig with two K3/100 radios, so right now, I bring both radios to my house and start over with the setup

I turn on control radio, then turn on remote radio, but nothing happen. I hear on the headpones a continue sound  like telephone sound, "u i u     u i u     u i u      u i u       u i u....................."   

I am following this two manuals:

Elecraft Manual http://www.elecraft.com/manual/K3%20Remote%20Owner%27s%20Manual%20%20Rev%20D.pdf  and

Remoterig Manual http://www.remoterig.com/downloads/RemoteRig_RRC1258-MkII_Users_manual.pdf

I couldnt open remoterig boxes to check inside as per Remoterig manual page 213

I update firmware on two remoterig boxes

I go to the browser and access microbit to go to radio settings. Here some diferences with manuals and browser
      - SIP password, Elecraft manual say blank, Remoterig manual say hello
      - SIP contact may I left blank or not?
      - Audio quality, Elecraft manual say "3 - aLaw 12 kHz" and remoterig manual say "2 - Linear 16 bits 8 kHz, so which one is the correct?
       - Codec Out Gain Elecraft manual say 250 and Remoterig manual say 255
       - Codec Imp Gain Elecraft Manual say 32 and remoterig manual say 14
       - Codec inp preamp Elecraft manual say "163", Remoterig manual say "Yes"


router setup also is diferent in Elecraft and Remoterig manuals on applications name, but maybe this is not a problem

Any idea what is wrong?

--
73,
Jorge
CX6VM/CW5W

Pages: [1]