Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - VO1HP

Pages: [1] 2 3 ... 8
1
Mike
In manual page 28 Advanced Settings it says K3 uses Yaesu settings F2000/5000/9000.  Your note says use Kenwood IF?  Please clarify.

Also I cannot find in the manual how to set the WebSwitch 1216H to interface with the RRC Remote box 1258 .  Is it required to interface to read the frequency of the radio?.  The WebSwitch does not have RADIO-RRC Settings page. 

I have port forwarded UDP port 13010 to the IP address of the WebSwitch and also have Automatic Control ON.  Also have set frequency range for two relays  80MSSB and 60M .  When I tune to those frequencies I cannot see any thing happen with the relays.

Also in 1258  Remote Box STATUS page ANTENNA-SWITCH IP = Not Connected.

I need a bit more info on how to setup.  Thank you.

73 Frank VO1HP

2
Ok Mike
Many tnx for the fast reply.  I will use the AS1289 manual and Kenwood IF  setting.   

73 VO1HP

3
I want to setup Antenna Selection function using WebSwitch 1216H.  Which Function Type do I use for my K3?

VO1HP

4
Skip
When I hear that Three tone  Alarm  here it usually means that no connection can be made to the remote 1258 by the Control 1268.  ...and that condition usually means a problem with the SIP address . It happened here a few days ago after a power failure at the remote.  WHen power was restored the WAN IP Address of the router  providing connectivity to the internet had changed. I was able to discover the new WAN IP Address at the remote location as I have a PC there that I access by using ANyDesk remote desktop software.....and can access the remote router admin page by typing 192.168.2.1 in the Chrome browser URL line.

 For some reason the dynamic DNS service did not pickup the WAN IP change.  I disabled the Dynamic DNS  and manually typed in the new WAN IP of the remote site into the SIP Connection box in the Control Radio Settings page.  There was no Alarm and Connection was made normally.

Did you verify that you have the correct WAN IP Address for the router at the remote end and are you certain the port forwarding is still intact at the remote router  for ports 13000, 13001,13002.?

73 Frank VO1HP

5
General / Re: Nano 1.6.4 stopped working
« on: 2023-06-18, 20:01:39 »
This info from mike SM2O

In 2018 we changed from our own licensing system to Google Play

To avoid that customer who has already paid once, have to pay again we use promotion codes

first uninstall the old App

go to the address below with your phone browser ( do NOT go to Google Play)

https://play.google.com/store?code.  Use Chrome browser NOT Samsung browser

copy and enter your personal promotion code below and install the PRO App, allow the App to use the Mic and other things it ask for during the installation

you should not get problems anymore as the App now is connected to your Google Account as every other App

and if you want to install the PRO App on an second device you will find it in Google Play and it will show that it's already payed

73 de mike

promotion code= To request code send email to info@microbit.sa

6
General / Re: Nano 1.6.4 stopped working
« on: 2023-06-16, 15:56:50 »

"No longer connected to remoterig license servers."
Last update May 10 2023.

Anbove is the message on the Playstore webpage for the App.  I reinstalled the App and got new license number.
Still cannot connect. 

What's going on?

7
General / Re: Nano 1.6.4 stopped working
« on: 2023-06-16, 15:14:58 »
I am now getting error message:
"Invalid App license".

How to get valid license??

Frank VO1HP

8
General / Nano 1.6.4 stopped working
« on: 2023-06-16, 13:33:03 »
My Nano 1.6.4 has stopped working. I am not getting any error messages.  Tapping CONNECT nothing happens.   Please help.

Frank VO1HP

9
General discussion forum / Re: K3 CAT and PTT at remote site
« on: 2022-09-05, 18:50:00 »
I now have been successful in setting up local CAT control of my K3 at the remote station.  I am using an Elecraft KXUSB cable from COM1 on the RR1258 Remote to the PC.  A virtual COM port 10 is created. I am using that port for local rig control and PTT using WSJT-X while I am at my remote. 

Com 1 set Mode 7 in Serial Settings.  For audio I am using a Behringer UMC202HD interface cabled to the K3 LINE IN/OUT jacks.

The only issue I have is a "slow" PTT.  The delay in making PTT is very noticeable but does not interfer with the decoding process.  My PC is ancient running Win 7.  There is a lot going on I guess with the inception on PTT from WSJT-X and the KXUSB Port and then the radio. 

I am wondering about the 1258 OUT0/1/2 settings currently:   CONNECT/BAUDOT RTTY45/ KEYER respectively.  I have tried changing OUT0 to PTT but it does not "take" when applied. 

Is there a solution for the lazy PTT?

10
General discussion forum / Re: K3 CAT and PTT at remote site
« on: 2022-08-08, 10:58:44 »
MIke
OK Tnx for the reply.  COM 1 is already set to Mode 7.  I will connect a cable from COM1 to the PC next trip to remote.
Serial settings
COM1 mode   
Mode-7, CAT to COM2 (local&remote)
COM1 baudrate   
38400
COM1 data bits   
8
COM1 stop bits   
1
COM1 parity   
0 - Off
COM1 rts/cts   
Yes
COM1 terminator (hex)   
00
    

RE your  second point:
"PTT can be connected in paralell with RRC PTT oout which is Open Collector"
Pls claify what is meant ...Do you mean in IOSettings to set like this:

IO settings
OUT0 mode   =PTT
OUT0 on/off       =ON   
    
VO1HP

11
General discussion forum / K3 CAT and PTT at remote site
« on: 2022-08-07, 22:20:48 »
When visiting my K3 remote site i want to operate 6M FT8 using the site Win 7 PC.   I can use the
Line in/out jacks on the K3 for audio but how to do CAT and PTT?

The COM 2 jack on the  RRC remote is occupied by the rs232 cable from the radio and i dont want to interfer with the cabling for the normal remote operation.  The COM 1 jack on the RR remote box is not in use.  Is there a way to use it to establish local CAT when i am at the remote site?

I cant figure it out reading the manual.

Frank VO1HP


12
I am in Canada ...there is no dealer listed .   Can I buy 1216H and 1216L direct from Remote rig??

73 VO1HP

13
I have three temperature sensors on WS Bus B.  They have stopped working.  No temperatures being shown on the web page.

What to look for ?...any help?

Frank VO1HP

14
General / Re: NANO Elecraft 1.6.2
« on: 2021-10-26, 01:10:54 »
Just discovered my error.  When I entered the new IP address I also appended the PORT (i.e. 156.xx.xx.xxx:364 ) for the Remote box.  That PORT is forwarded in the remote router to the LAN IP address of the RR Box.  As a test I removed thet  ":364" and i connected immediately.  How come??   I thought a had to forward to the PORT for the RR Box IP?
Can someone clarify?

FR\rank VO1HP

15
General / NANO Elecraft 1.6.2
« on: 2021-10-26, 00:43:37 »
I have not used the Elecraft NANO App on my Android phone for a while.  Trying it today but cannot login.  There is a new IP Address which I am using.  The App doesn't do anything when I press CONNECT and after a few minutes displays TIMEOUT  Could the Lic.ID have expired?

Frank VO1HP

Pages: [1] 2 3 ... 8