Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - KB8CR

Pages: 1 2 [3] 4 5 ... 7
31
General discussion / New 1274B ???
« on: 2015-09-05, 07:16:15 »
What is the difference between the dongle I have, and the "new" one?

Charlie KB8CR

32
That would be an awesome application !!

Charlie KB8CR

33
I have finally found a solution for running PSK31 with HRD + DM780 on the RRC Micro.
http://www.vb-cable.com has a free virtual cable (only 1 input and 1 output) that I installed and select it in RRCMicro as the mic and speaker selection. Do the same in DM780. Set the levels by HRD's AF gain control for RX and adjust mic gain, and it all works perfectly. I have worked quite a few stations today. Taking the notebook with me to Florida tomorrow, and will try it over the internet, but no reason it shouldn't work just fine.

Charlie KB8CR ;D

34
General / Re: RRC nano demo
« on: 2014-09-27, 05:08:05 »
Can't wait for the IC-7100 version !!

35
General discussion / Re: android/iphone/win app?
« on: 2014-07-01, 04:01:59 »
Hi there hb9edm.

We are working on it and things are going quite good.
Hope to have some kind of test version on soon with the most important functions in place.
This version will work against TS480

Here is a screenshot on whats going on  :-X

That looks great.......just hope there is an iOS version down the road that works with the IC-7100  ;D

36
General discussion / RRC-Micro beta release CW issue
« on: 2013-11-15, 02:21:19 »
Love the new interface, all working great except for Macros. When sending longer macros, such as a 3x3 CQ, it only sends a short part of the macro and stops. When typing in the window, all is perfect.

Charlie KB8CR

37
That is interesting. I am using 1.6.10 on a Windows 7-64 bit notebook with wifi connection without any issues.

Charlie KB8CR ???

38
Maybe I'm wrong.... :-\   It may be the "=" character that everyone sends between comments.

Thanks again.

Charlie KB8CR

39
 :D
Thanks, Roland. Tried a few QSO's on the new release. Seems to work FB. One VERY minor error.

For the "-" character, it sends -....-   instead of  -...-

Other than that, it's great. I really like the extra Macro spots.

Thanks again. 

Charlie KB8CR

40
Mike:

Have you tried it? Just want to make sure it's not just on my end. The older version(s) still work here (with their own problems however). But while the new version looks great, it's just not sending the cw correctly at all.

Charlie KB8CR

41
Roland:

Unfortunately, the new version 1.6.9.0 is not sending CW ok. Whatever I type in, or if I use a macro, it only sends a few PARTS of characters. Don't know what could be wrong.

Charlie KB8CR  :-\

42
Looks great ! I'll try it out tonight.

Charlie KB8CR

43
General discussion / Re: Microbit RRC Client - won't connect
« on: 2013-10-12, 22:46:50 »
I was just reading on the web about VPN's and port forwarding. I found the following:

  • What sort of VPN are you wanting to use. If it's PPTP then you will need to forward TCP/1723, and Protocol 47 (GRE).
     For IPSEC you will need UDP/500 and Protocol 50 (ESP).

  • You are only forwarding the UDP and TCP protocols. GRE and ESP are protocols, not ports. If the DMZ function assigns a public IP address to your server then it is likely that your router cannot forward these protocols via NAT. Some router cannot forward GRE or ESP protocols

So, it MIGHT be your router. Just a thought.

Charlie KB8CR
[/list]

44
General discussion / Re: Microbit RRC Client - won't connect
« on: 2013-10-12, 22:37:18 »
I don't use a VPN, and don't know much about them, but are there configurations for it? Port 80 is normally open on all systems, but it might be that ports 13000-13002 aren't making it thru to the box.  Looking at your configuration I don't see any glaring problems.

Charlie KB8CR

45
General discussion / Re: Microbit RRC Client - won't connect
« on: 2013-10-12, 21:32:39 »
You need to make sure that you are port forwarding Ports 13000, 13001, 13002 to the RRC-Radio box.

Charlie KB8CR

Pages: 1 2 [3] 4 5 ... 7