Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DL5FAB

Pages: 1 [2]
16
General discussion forum / Re: USB-Interface stopped to work
« on: 2010-02-05, 23:11:57 »
Hi,

meanwhile, many trials further I have my configuration working proper but the problem with the USB interface on this Controler Unit remains and I concluded that I damaged the USB interface. As I can configure the unit through the Web interface reliably, I did not take any further action for now. I will send it for repair, when I have some time left.

17
General discussion forum / Re: USB-Interface stopped to work
« on: 2010-01-20, 22:06:39 »
I did more tests today:
Downloaded the latest firmware version and up-dated through the web interface. Application Upgrade reports ok. Bootloader Update reports error.
What is actually the difference between these two options?

DHCP switched-off and DDNS deactivated.
RRC 1.01 version  installed on PC.

When I connect the USB interface the Controller start to re-boot constantly. The PWR LED goes off, the Red Led on the Aux/Mic goes on for some time and than it repeats.

When I re-install the driver under XP it reports as a USV Videodevice.

The RRC Manager does not recognise the unit to be connected.

Through the web interface everything looks fine.

73

Manfred

18
This is what I also thought. Port 5060 is used by Vodafone for the VoIP but in my case it is not forwarded into the LAN (I hope). I made a test with Port 5070, which works fine but does not solve the problem with the firewall. I managed today to set-up connection via O2 UMTS Pre-paid from Controller to Internet and Radio on the the DSL connection but still with Firewall switched-off. Manfred

19
General discussion forum / Re: USB-Interface stopped to work
« on: 2010-01-19, 23:18:18 »
Hi Carsten, this looks very similar to my problem. I used the DynDNS and DHCP. I will do some more test.

73

Manfred

20
General discussion forum / USB-Interface stopped to work
« on: 2010-01-18, 20:47:04 »
Following delivery of the units, I had installed the latest firmware version 2.01 on the Controller and Radio part and using the USB interface for configuration intially worked fine. At some point of time, even so the RRC Manager reported connection to the unit, I could not retrieve or download any information from/to one of the units (Controller). I have re-installed the RRC Manager SW on the PC, I have re-installed the device driver on the PC, used another PC with the driver installaed but it appeared not to work anymore.
Configuration through the Web interface is still fine. Resetting the unit, even to the original delivered state and re-installation of the firmware through the web-interface did not bring success. I fear that the USB interface could be damaged?
Any idea?
 
73 de Manfred, DL5FAB

21
Reaching the Radio Controller over the Internet voia DSL-Line and Vodafone Easybox A 600 W-LAN router works fine with the firewall switched-off. However, the following ports are opened than:
                          Radio Controller    LAN                                  WAN       Public IP
155   UDP   192.168.1.228   5060   188.107.211.158   5060   82.113.106.106   3459
156   UDP   192.168.1.228   12000   188.107.211.158   12001   82.113.106.106   12000
157   UDP   192.168.1.228   11000   188.107.211.158   11001   82.113.106.106   11000
158   UDP   192.168.1.228   12000   188.107.211.158   12000   82.113.106.106   13930
159   UDP   192.168.1.228   11000   188.107.211.158   11000   82.113.106.106   19643
160   UDP   192.168.1.228   5060   188.107.211.158   5060   82.113.106.106   3459

I do not undersand the outgoing ports number 12001 and 11001. Can somebody explain?

I have tried the following:
Firewall switched on and Radio Controller into DMZ area. Port Mapping activated as follows:

Nr. LAN IP           Protokolltyp LAN Port Öffentlicher Port Aktiviert Einstellen
1    192.168.1.228 UDP 5060 5060     
2    192.168.1.228 TCP 80 80     
3    192.168.1.228 TCP 23 23     
4    192.168.1.228 UDP 12000 12000     
5    192.168.1.228 UDP 11000 11000     

this does not cure the problem. The Radio Controller Web Server is perfectly reachable through the firewall.

Can somebody give me a hint?

73 Manfred, DL5FAB

 

Pages: 1 [2]