Messages

2341

General discussion / Re: COM 1 with version 1.5.1

« on: 2012-04-13, 23:40:07 »

I guess you have exactly the same settings in the Radio-RRC and the same cables as when you use the box to box setup. Softwares like the one for 1k-FA is not written to be able to connect over internet so it's tricky. The virtual serial port which are now implemented in the RRC-micro software, now behaves as much as possible like a hardware serial port. That's why all other radio control software works, and if it doesn't work now with the 1k-FA, I'm sorry to say it but I don't think there is much hope, if they don't modify their software.

I think the best way to solve this would be if we could make a web based control like the one to the ACOM-2000 (RC-1216H).


73 de mike

2342

General discussion forum / Re: FT-2000 twin disconnects when changing main VFO frequency

« on: 2012-04-13, 15:51:51 »

OK Guy

Nice to hear that.

73 de mike

2343

General discussion / Re: char by char option

« on: 2012-04-13, 06:39:59 »

Hi

The disadvantage with "char by char " is that it need lot of bandwidth, for every char sent, 16 char are sent over the Internet. So for that reason it's better to use an other mode if it's possible. For controlling a rotor it doesn't matter as very little data is sent and only when turning the the antenna. But using "char by char" for radio control when tuning the VFO can give huge data package which can affect the audio if the bandwidth is limited.

73 de mike

2344

Konfiguration av RRC 1258 / Re: Kun grønn lampe på Ethernet RRC-1258 MkII: Radio

« on: 2012-04-11, 09:35:50 »

Gul lampa visar bara om den är ansluten med 10 eller 100 Mbit. Det spelar ingen roll. Får du kontakt med via webinterfacet så är det nog bara någon inställning som är fel, som gör att kontrollburken inte får kontakt med radioburken.

73 de micke

2345

General discussion forum / Re: RRC-Micro audio

« on: 2012-04-08, 10:50:10 »

Hi
You are free to select which soundcard/USB device you want in the RRC-Micro software (in the connection setup dialog). But we decide to include our own soundcard in the USB/PTT dongle to be sure there is a working soundcard that we can support. As we are working with so small buffers it is very important that the sampling frequency is very accurate in the soundcard (eg a a hiqh quality crystal). But I haven't heard that there is any problem to use other standard soundcards/USB devices.

73 de mike

2346

Konfiguration av Routrar och Brandväggar / Re: Mobilt Bredband och datamängd?

« on: 2012-04-07, 13:00:06 »

50 G Byte räcker till 1700 timmars lyssning med audio quality = 0 men och andra sidan räcker 0,5 Mbit/s bandbredd för lyssningen så det spelar ingen roll om dom drar ned. Men några barn som sitter och tittar på film på paddorna har ju snabbt förbrukat dom G Byten

73 de micke

2347

General discussion / Re: RRC-Micro PC and ICOM IC-E2820

« on: 2012-04-07, 09:12:55 »

The RRC-Micro doesn't bother about what radio you use. But as far as I know there is no support for IC-2820 in HRD or other PC-software.
There is only some memory setup program from ICOM.


73 de mike

2348

General discussion / Re: RRC-Micro PC Client do not wotk with HRD 5.11

« on: 2012-04-07, 09:08:57 »

Using PTT inside HRD will send a command to the radio to do PTT but not open upp the audio path. That's nothing to do about it. The principle for RRC-Micro is not decode what is sent between HRD and the radio just transfer the data. So that is the way it has to be. We should remember that the RRC-Micro is a complement for travelling and portable use and it will never replace the hardware boxes 100% thats not our intention.

73 de mike

2349

Konfiguration av Routrar och Brandväggar / Re: Mobilt Bredband

« on: 2012-04-05, 21:15:40 »

Hoppas någon som har Telenor kan svara på det. Det är inte säkert det behövs nått tillägg numera. Det är ju så vanligt nu att man behöver åtkomst utifrån så man kanske öppnat den möjligheten på alla abonnemang.

73 de micke

2350

Hardware, Cabling, Installations / Re: RRC-1258 Radio cannot be Radio settings.

« on: 2012-04-04, 18:35:51 »

Hi

Email me "Exported settings (html)" files  from both units.


73 de mike

2351

Configuration, RRC 1258 / Re: Transparent Serial Channel on 1258 MKII

« on: 2012-04-03, 18:19:18 »

Hi

set radio mode to 3
and try with com2 mode = mode 3. If it doesn't work set com2 mode = mode 1

/mike

2352

Configuration, RRC 1258 / Re: RRC and the Icom 9100

« on: 2012-04-03, 18:07:08 »

Hi

You do not discribed how you have connected the cables. Normally the CI-V cable is connected from the Radio-RRC TTL connector to the Radio CI-V jack.

If you connect the PC with a serial connector to Control-RRC com2 you have to set com2 to "Logically in parallell with com0"

If you use USB connection from the PC set "Use USB Com Port as COM0" = yes

On the status page you can see that all communication is OK

The RRC do not bother about the CI-V adresses.

I don't know what mean by laptop at the remote end. Remote end for me = radio end, and there is no PC needed

73 de mike

2353

General discussion forum / Re: New Remoterig

« on: 2012-03-31, 23:28:04 »

Hi

It's dangerous  to make something specially for a rig like for example TS-480. The day the development is finnished, they can close down the production. You never know in advance
But there will be a WLAN card  that can be placed inside the RRC-box available in a couple of month

73 de mike

2354

Configuration, RRC 1258 / Re: K3 Twins - Initial Feedback

« on: 2012-03-29, 23:12:19 »

K3 utility can be used in the same way as a log program via com1. Set com 1  to mode 7 in both RRC. As far as I know everything works but upgrading the K3-softwares. There is a few known errors in the K3 firmware which Wayne will fix as soon as the load from the KX3 development  is lower. Concerning the RRC there is no known bugs. You can send feature requests etc via email

73 de mike

2355

General discussion forum / Re: Wireless Device (eg. Phone, Pads) - Program Mode

« on: 2012-03-26, 22:12:30 »

Hi Jose
The protocols are based on standard SIP, RTP etc. During the years we have added features which is not standard so I doubt it works with standard softwares. We have no secrets but we have no intentions to make an open specification as we have enough to do to support our own softwares.

73 de mike