Messages

2356

General discussion forum / Re: Wireless Device (eg. Phone, Pads) - Program Mode

« on: 2012-03-26, 16:37:51 »

You need a pair of RRC-1258MkIIs or the RRC-Micro PC-client and a RRC-1258MkIIs connected to the radio. You can not connect from a phone or pad.

73 de mike

2357

General discussion forum / Re: RRC1258 software suggestion

« on: 2012-03-23, 09:12:08 »

It's not possible to switch of the audio streams totaly there need to be some data sent to keep up ports and there are some signaling also, but if the audio (codec) data is removed the amount of data will be significantly reduced. I have thought before about making a level sense function which could switch on/off the audio data when no audio is comming from the reciever, eg. when squelch is closed. I think a function like that will be useful for more users. I don't think there is many user who send the audio via a UHF repeater, but there are a lot which use 3G/4G connections.

73 de mike

2358

Hardware, Cabling, Installations / Re: K3 Twins + Expert Amp + Band Decoder + Steppir ..O my...

« on: 2012-03-22, 17:05:24 »

Hi

I cant say exactly how to do, but the important thing is not to make any Y-cables between K3 and RRC. Do as Mitch say set com 1  in mode 6 or 7 and connect your stuff to com1 of the RRC. outside the RRC-com1 you can try with Y cables etc.

73 de mike

2359

Configuration, RRC 1258 / Re: TIMEOUT PROBLEMS

« on: 2012-03-22, 16:06:56 »

Timeouts is probably caused by the Internet connection not the firmware. But upgrade anyway there are lot of enhancements since 2.28. You can upgrade direct, but check up your settings afterwards. When upgrading so many versions the settings can be affected

73 de mike

2360

General discussion / Re: RRC-Micro PC Client do not wotk with HRD 5.11

« on: 2012-03-22, 07:08:01 »

Im sorry I don't know what you mean. The existing published versions of RRC-Micro 1214A are compatible with HRD and RS-BA1 and has been for years. The new version will also support other softwares like TRX-manager, ARCP-480, Yeasus PCC-950 , PCC-2000 etc. We are still waiting for a third party vendor to do their job before we can publish the new version.

/mike

2361

General discussion forum / Re: Icom 7600

« on: 2012-03-20, 08:18:20 »

Hi

It's not possibel, as both the RRC and the IC-7600 has a "USB device" port, and two devices can not communicate.

73 de mike

2362

Allmänt diskussionsforum / Re: Nästan inget ljud vid uppstart. IC-706 MkIIG

« on: 2012-03-19, 13:13:41 »

Hej

Det finns inga indikationer på att det skulle ha nått med Remoterig syystemet att göra.

73 de micke

2363

General discussion forum / Re: control Yaesu FT9000 with FT2000

« on: 2012-03-16, 08:25:17 »

Hi

We have tested most combinations but not controlling a FT-9000 from FT-2000. Try to contact w6df Jim they have tested various combinations with FT-9000. The QRZ.com email adress is OK.

73 de mike

2364

Hårdvara, Kablage, Installationer / Re: CI-V med RRC-1258 v1

« on: 2012-03-15, 14:59:34 »

Om du skall köra CI-V samtidigt som du kör manöverpanel så måste du använda dem på framsidan

73 de micke

2365

General discussion / Re: Kenwood TM-D710 and RRC-Micro PC Client

« on: 2012-03-14, 22:27:49 »

No I do not think there is any program that can control the TM-D710. But if just want to use a already selected channel and just use audio and PTT it's OK

73 de mike

2366

Hårdvara, Kablage, Installationer / Re: CI-V med RRC-1258 v1

« on: 2012-03-14, 22:24:58 »

Jo men eftersom du redan använder COM0 för panelen så måste du ha ett separat CI-V interface från COM1 till radions CI-V kontakt, tex CT-17. Du kan också bygga ett själv men tänk på att du måste spänningsmata det separat, en del ritningar på nätet tar spänningen från RS-232 kontakten, men det går inte på RRCn. Sedan ställer du bara in COM1 på CI-V mode och samma baudrate som du ställt in radion på tex 19200 baud. På kontrollsidan kan du ha en rak RS-232 kabel men på radiosidan måste du ha en där pin 2 och 3 är korsad om du ansluter en CT-17

73 de micke

2367

General discussion forum / Re: TS-480 TOGETHER WITH PRO SET 5 HEADSET

« on: 2012-03-14, 13:04:44 »

I use a heil pro set my self and a adapter from Heil I think, As far as I remeber the RJ45 is red on it, I put it direct inte to the RRC MIC/AUX connector and it's no problem. It cant be much more that the adapter cable which is the problem. I assume you have removed JMP1 to avoid DC to be feed to the MIC element.
73 de mike

2368

General discussion forum / Re: FSK

« on: 2012-03-13, 22:08:15 »

You do not have to select it anywhere in the Control-RRC, COM FFSK is always active, but you must select what output you want to use for FSK/RTTY in the Radio-RRC.

73 de mike

2369

General discussion forum / Re: Need help to install TS-2000

« on: 2012-03-13, 16:00:37 »

Hi

Then it's probably the "SIP contact IP" which is wrong in the Control-RRC. You can email me exported settings(html) from both unit so I can check them

73 de mike

2370

General discussion forum / Re: Need help to install TS-2000

« on: 2012-03-13, 08:48:28 »

Hi

The last 3-4 hams I have helped with the TS-2000 has all had the same problem. The control cable from Radio-RRC to TS-2000 has not beed made straight, pse check yours. If you use the orginal cable from RC-2000 to Control-RRC, and all settings are OK but the cable is wrong and, you will see that the the Yellow LED at the AUX/MIC will light up when you press PWR ON button. Also check the red straps, they are not needed for the system to connect, they are just for the mic signal, but if they are placed in wrong positions they can interfere with the communication as the COM0 is present at the socket also.

73 de mike