Messages

2371

General discussion forum / Re: FT-2000 twin disconnects when changing main VFO frequency

« on: 2012-03-11, 00:08:43 »

Hi

Yes I remember it now when Guy write it. Before you change back. Try to log what happens.

anslut med telnet till control-RRC, tryck på d så du kommer i debug menyn, välj 0 för att aktivera debug på com0, Gör det du gjorde för att den skulle starta om. Kopiera loggen och skicka så kanske vi kan se vad Yaesu ändrat i protokollet. Det kan vara svårt att hitta utan att ha radion på plats men vi kan ju alltid göra ett försök

/micke

2372

Allmänt diskussionsforum / Re: Innslagsproblemer på 160 meter

« on: 2012-03-09, 16:44:47 »

Jo problemet är ju att inte ADSL modemet tål sändning på 160m. Enligt uppgift skall det bli bra om man ställer in modemet så att det inte utnyttjar ADSL 2+. Netgear modem vet jag att går att ställa in så. Man får då högst 2 Mbit men det kan det kanske vara värt om det går att köra då.

73 de micke

2373

iPhone App / Re: iPHONE app...

« on: 2012-03-07, 20:14:11 »

Nu har vist Apple accepterat Appen till slut efter 14 dagars funderande, sök webswitch på AppStore

/micke

2374

iPhone App / Re: iPHONE app...

« on: 2012-03-07, 16:06:10 »

Hej

Den har varit hos Apple i 14 dagar för påseende. Det är inte som med Aandroid att man bara kan publicera appen. Apple skall ha reda på allt om företaget, och allt annat tänkbart, skonumret på programmeraren var nog med också. Inte nog med det, dom skall tydligen prova att den funkar mot Webswitchen också innan den publiceras. Det är otroligt att det finns så många Appar på AppStore trots byråkratin kring detta.

/mikael

2375

Hardware, Cabling, Installations / Re: Low audio + lf-hiss FT-2000 twin

« on: 2012-03-07, 15:16:31 »

I tested with a FT-950 which I have here, the output in the headset jack is 10 dB lower than the speaker output when connected to the RRC ( I do not know if it is the same in the FT-2000). With the volume at 12 o'clock and a speaker direct to the speaker jack on the Control-RRC it's still to high to listen to  a carrier when the Radio-RRC  is connected to the speaker jack. But anyhow you can compensate for those -10 dB by setting "codec inp gain" in the Radio-RRC to 13 (13x0,075=9,75). Another way is to remove one or both of the 100 ohm load resistor(s) in the Radio-RRC to reduce the load.

73 de mike

2376

General discussion forum / Re: Dual ts-480 control panel

« on: 2012-03-07, 11:30:34 »

Not in parallel, but you can put a relay controlled by one output at the Radio-RRC which disconnect the local control panel automatically when you connect over the remote.

73 de mike

2377

General discussion forum / Re: RC1216H for SPE Expert 1K-FA

« on: 2012-03-07, 07:59:25 »

Hi

No the Expert 1k-FA has no third party control Interface, you have to transfer the serial port and use their own PC-software. It can be transferred over com1 in the RRC:s

73 de

2378

Configuration, RRC 1258 / Re: Remoterig FREE Dynamic DNS service

« on: 2012-03-06, 20:31:28 »

Hi Don

It's no known problem at all with remoterig ddns. It should work if you upgrade the firmware and do as the manual says. I just checked and there is no update from s/n 2629 yet. You can see on the radio-RRC status page if the ddns is OK.

73 de mike

2379

General discussion forum / Re: RotorCard - RS-232 rotor control for Yaesu DXA and DXC series Rotors

« on: 2012-03-06, 08:27:53 »

Yes

both the Webswitch and the RC-1216H supports DCU-1 protocol which is used by idiompress

73 de mike

2380

Hardware, Cabling, Installations / Re: RRC-radio no power LED

« on: 2012-03-06, 08:26:20 »

Are you sure that you have the right polarity on the PS. Positive should be in the centre of the connector. The X100F RRB2 is a Automatic fuse, and if it's hot something is consuming to much power.

/mike

2381

Hardware, Cabling, Installations / Distorted audio caused by RF feedback on early Elecraft K3s

« on: 2012-03-05, 15:25:18 »

Thor TF4M who has a very early K3, had problem with distorted audio caused by RF feedback when he was installing his remote station. After lot of troubleshooting he found the Application Note from Elecraft.

http://www.elecraft.com/K3/mods/K3_Application_Note_Front_Panel_Microphone_Grounding.pdf

This was probably the solution, but instead of making this recommended change, hi made a new cable and connected the RRC to the K3 back mic input instead, and all problem was gone.

73 de mike

2382

General discussion forum / Re: RC1216H to control a SteppIR antenna and a rotator

« on: 2012-03-05, 14:54:03 »

Hi

A RC-1216H can not control both the Stepp-IR and the rotator at the same time. You need to have two or a a RC-1216H and Webswitch-1216H (with the extra serial cable). Which also can control the rotator.

73 de mike



 

2383

Hardware, Cabling, Installations / Re: Low audio + lf-hiss FT-2000 twin

« on: 2012-03-05, 11:28:04 »

The load on the Audio input to the Radio-RRC is 50 ohm. If the radio can't produce enough audio with 50 ohm load  the levels will be low. There is nothing which can be changed by jumpers. I have not noticed any problems with the levels when we tested with FT-2000, but we do not have any FT-2000s now to test with. Test to use the speaker output on the back instead.

/mike

2384

General discussion forum / Re: RRC1258MKII Control disconnecting after 2 minutes

« on: 2012-03-05, 08:30:59 »

Hi

I connected from here (sweden) to your radio, and it works perfect. Even very low latency. So your Radio-RRC and the router at the radio site is set up OK. I can t see the other end. But at least you know where to look. Not much to antenna connected I guess, only a few weak signals on 20m heard.

73 de mike

Name   Value
Control panel   ON
Radio   ON
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(44)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
Current audio packet size   20
Current audio quality   0 - alaw 8 kHz
SIP Out port   5061
SIP In port   5061
Audio Out port   11000
Audio In port   11000
Command Out port   12000
Command In port   12000
External SIP In port   5061
External Audio In port   11000
External Cmd In port   12000
Other party   74.89.231.113
Input 0   High
Input 1   High
Input 2   High
Output 0   High
Output 1   Low
Output 2   Low
DNS status   OK, remoterig.com = 193.202.110.185
Active profile:   wx1ct
PTT status:   OFF

2385

Hardware, Cabling, Installations / Re: Low audio + lf-hiss FT-2000 twin

« on: 2012-03-04, 23:16:37 »

The audio input to the Radio-RRC are made for "Speaker level" not line out. If you connect it to the phones output or speaker output it will be OK

73 de mike