Messages

2401

General discussion forum / Re: Control end wont boot when IN0 is active

« on: 2012-02-18, 09:42:16 »

IN 0 is not allowed to be low at power up. That's the same in all hardware versions and is not possible to change with software.

The bootloader is no involved in how the webpages looks like. It's only used to start up the main program, flashing new firwares etc. We not yet done any modifications to the bootloader that makes it necessary yo upgrade it from the orginally installed versions.

73 de mike

2402

Configuration, RRC 1258 / Re: No connection with ddns

« on: 2012-02-13, 16:18:24 »

I do not think the disconnection has anything to do with the RRC.s or the ddns. it's probably a network/internet issue.

Install pingplotter www.pingplotter.com and run it against your radio-qth, then you will see if the network connection is down when you got the disconections.

73 de mike

2403

General discussion forum / Re: FSK

« on: 2012-02-12, 20:45:44 »

Hi

The easisest way is just to split the audio from the 3.5 speaker jack. Thats how I do my self I use the signalink USB.
It also possible to connect a cable from the signalink to the TTL jack where audio is present between pin 1 and 6

73 de mike

2404

Hardware, Cabling, Installations / Re: Yaesu 857

« on: 2012-02-10, 17:55:40 »

Hi

I have attached an idea to cables which can be used if you do not want to do any mods on the pcb. pse try.

There will be boxes which can be used without mods in the future.

73 de mike

2405

General discussion forum / Re: Incorrect temp display in 1216E

« on: 2012-02-10, 17:14:46 »

Ok

It's not many days per year the temp is between 0 and -1 here and I might not have checked those days as I do not log the temperatures. We will check if there is done some improvements between 1.01 and 1.07

73 de mike

2406

General discussion forum / Re: Incorrect temp display in 1216E

« on: 2012-02-10, 16:41:35 »

Hi

I use four 1216E for temperature control my self and I have never found any problem with them, they show outdoor temps below zero now, all of them. It's firmware version 1.07 in them.

73 de mike

2407

General discussion forum / Re: Work Web Switch with ProSisTel PST110?

« on: 2012-02-08, 08:55:24 »

If it works or not are not depending on the Rotator. It's depending on the computer protocol which the Controlbox uses. As far as I can see it's the same D-box protocol as for the other Prosistel.

73 de mike

2408

General discussion / Re: FSK

« on: 2012-02-08, 08:25:03 »

Hi

No it's not possible. There is no such plans for the moment either.

73 de mike

2409

Hardware, Cabling, Installations / Re: Yaesu 857

« on: 2012-02-07, 12:23:07 »

Hi

It's possible, but the porposed mods takes less than 5 minutes. So we concidered it to be much more complicated to make splited cables. If you do don't forget the screeing of the mic wire on the radio side.

73 de mike

2410

General discussion forum / Re: VOX setting and CW on the TS-480

« on: 2012-02-04, 18:07:17 »

The Remotrig system does not know anything about the TS-480 settings, it always transfer the CW-keying signal to the radio. Then it's up to the TS-480 to decide what to do with it.

73 de mike

2411

Configuration, RRC 1258 / Re: Dynamic DNS Status: Error Code 9

« on: 2012-02-02, 22:55:38 »

Yes then the DDNS address is OK but the DNS adress on the IP-settings page is wrong. The RRC can not contact the same DNS as your PC. Check what DNS the PC use and set the same into the DNS address field in the RRC.

ddns and DNS is not the same thing

73 de mike

2412

Konfiguration av Routrar och Brandväggar / Re: Mobilt Bredband

« on: 2012-02-02, 22:23:59 »

Vad jag vet så funkar det lika bra med Telia, Tele2, Tre och Net1 däremot har man behövt speciellt tillägg till Telenor abonnemang men det kanske inte behövs nu längre.

Här uppe är det ju bara Telia och Net1 som är verkliga alternativ, kanske annorlunda i SM6

73 de micke

2413

Configuration, RRC 1258 / Re: Dynamic DNS Status: Error Code 9

« on: 2012-02-02, 22:19:00 »

If you can use the ddns adress from your PC but not from the RRC when they are connected to the same router you have setup the dns wrong in the RRC. check with ipconfig what dns the pc use and set up the RRC so it use the same dns adress as the pc. In 99% of the cases the gateway and the dns adress is the same and = the LAN ip adress of the router.

73 de mike

2414

Configuration, RRC 1258 / Re: RRC-1258 MkIIs and Yaesu, K3, Icom

« on: 2012-02-01, 09:31:57 »

Hi

I recommend them to use a Standard RRC-1258MkIIs Control RRC to be able to use CW and all other features. It's  also possible to use the RRC-Micro PC-Client with it's limitations.

73 de mike

2415

Configuration, RRC 1258 / Re: RRC-1258 MkIIs and Yaesu, K3, Icom

« on: 2012-01-31, 16:15:20 »

Hi

To use two Yaesu in twin setup for example FT2000-FT2000 you must have the Yaesu Twin package.
All other are the same and Yaesu twin version work for all other combinations.

K3-Twin is standard version but with all cables included in one package.

73 de mike