Messages

2476

Konfiguration av RRC 1258 / Re: ddns remoterig

« on: 2011-12-12, 22:06:21 »

Hej. Det var bara från början vi hade skrivit fel serienummer i databasen. Nu skall det funka med alla. Vad har din burk för serienummer ? vad står det på status sidan om Dynamic DNS status ?

73 de micke

2477

General discussion forum / Re: Remote works fantastic

« on: 2011-12-07, 09:46:30 »

Hi Lee

With the Antenna setup you have in Summit I think you should consider the K3 Twin or Yaesu Twin solution to be able to use a radio which match the Antennas. Both those solution gives the same feeling as with the IC-706 with the front panel.

73 de mike/sm2o

2478

Configuration, RRC 1258 / Re: Remoterig FREE Dynamic DNS service

« on: 2011-12-05, 23:19:05 »

Hi
pse send me a print screen of the dns page and the status page by email to mikael(a)microbit.se

73 de mike

2479

General discussion / Re: Exactly what is wrong!

« on: 2011-12-05, 15:54:28 »

I have mailed you

/mike

2480

Configuration, RRC 1258 / Re: Remoterig FREE Dynamic DNS service

« on: 2011-12-05, 12:20:09 »

We found that we where not accepting serial number lower than 3300. If yours where lower than 3300 that could be the reason. We have fixed that. If you try again and it doesn't work, check the Dynamic DNS status on the Status page and let us know the result

73 de mikel

2481

General discussion / Re: Exactly what is wrong!

« on: 2011-12-02, 17:10:16 »

Maybe there is some differences in timing between different FT-2000. Setup portforwarding for port 23 (telnet) and email me the info we need to connect to your Radio-RRC. We will test on Monday when the software guys are at the office.

73 de mike

2482

General discussion forum / Re: RRC1258 Fails to boot

« on: 2011-12-02, 12:30:08 »

IF the red and yellow stays on the processor never start the main program. Reset the box to Factory default by pressing the Reset button for 30 sec. Connect a serial cable to COM1. Start a terminal program in the PC set to 38400 baud, 8 bit, 1 stopbit, no parity, no handshake. If the bootloader in the box sends some text to the terminal it's possible to upload a new firmware via X-modem. If no text shows you better send the PCB to us.

73 de mike

2483

General discussion forum / Re: Dyndns no longer free?

« on: 2011-12-02, 12:21:32 »

from RRC v2.48 we have introduced our own Dynamic DNS service. It's described in the manual.

73 de mike

2484

General discussion / Re: Exactly what is wrong!

« on: 2011-12-01, 18:15:37 »

Cables are important some times, even in this wireless world. Good luck

/mike

2485

Configuration, RRC 1258 / Re: IC-706mk2g separation cable cw configs and other questions

« on: 2011-12-01, 16:38:18 »

Hi

You must use the pot to disable the sidetone of the IC-706 it's not possible to do from the menu.

I think you have not Enabled the Keyer in the Control-RRC if you do not hear the sidetone from the RRC.

73 de mike

2486

Configuration, RRC 1258 / Re: IC-706mk2g separation cable cw configs and other questions

« on: 2011-12-01, 16:16:41 »

Hi

The sidetone for the Internal CW keyer is generated in the Control-RRC and you should hear it without even switching on the IC-706. If you can't live with the behaviour of the internal keyer without switching on the IC-706 it's not much to do, then you have to use your own keyer. It sounds strange beacuse I have really skilled CW operator friends which have no problem using the internal keyer.

Then when starting to test with the IC-706 remeber to turn down the CW-sidetone with the pot on the side of the IC-706 body. With 80 ms ping time I should set "key delay ms" to 100 ms to start with. Then let somebody else listen to you over the air. You can't listen to the transmission and using the paddles, it's impossible with more than 100 ms delay.

You can use the serial ports for Rotator and loggin, no problem it's just a matter of cables and settings

73 de mike

2487

General discussion / Re: TS-480

« on: 2011-12-01, 15:53:08 »

Yes if jmp3 is in place and you use a straight cable with wies fro pin 2,3,5,7,8 then pin 7 and 8 will be connected together in the RRC.

73 de mike

2488

News / New firmware for RRC-1258all. v2.48

« on: 2011-12-01, 15:46:35 »

A new firmware for the RRC is released v2.48.

-New function: Support for Remoterig dynamic DNS.
-New function: Pwr on/off command  for Yaesu FT-450/950/2000/5000/9000

The pwr on function was developed to take care of PWR on FT-2000 when controlling it from HamRadioDeLuxe but can probably be useful in other situations also.

73 de mike

2489

News / Remoterig FREE Dynamic DNS service

« on: 2011-12-01, 15:41:47 »

Since DynDNS has stopped offering free Dynamic DNS Services we have built our own Remoterig dynamic DNS service. This service is for Remoterig and Microbit products only and is of course free. No registration is needed the function is automatic and based on the serial number of the Equipment. The remoterig ddns client is included from firmware version 2.48. The settings needed to activate the ddns function are described in the Users manual version A17.

73 de mike

2490

General discussion / Re: Exactly what is wrong!

« on: 2011-11-30, 17:59:27 »

The pwr on/off function has nothing to do with the pc client or setup of HRD.
It's sent when SIP ocnnection is up, independent of the control side. It will send the message even if you use box to box solution. You should use radio mode 4 or 10 and enable the function under advanced settings.

The problem with old PC softwares accepting virtual com ports has nothing to to with if RTS/DTR etc.  is used or not, the problem is on a totally different level.

I assume you have coonected pin 7 and 8 and set jmp 3 in place.

73 de mike