Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sm2o

Pages: 1 ... 165 166 [167] 168 169 ... 201
2491
General discussion / Re: Exactly what is wrong!
« on: 2011-11-25, 15:34:27 »
Hi

there is a new firmware version with support for Yaesu pwr on/off. The function is activated under the Advanced menu. I hope it will solve your problems.

73 de mike


http://www.remoterig.com/firmwares/RRC-1258-CRC_v2.47_2011-11-25.zip


2492
If you activate the "PTT activated by keyer" the PTT is activated before the "Key delay ms" time so if you set a key delay time you get the function you need plus you use the buffer for keying and get a more robust keying signal. It works in the same way even if you use an external keyer connected to the "straight key" input with the keyer activated.

When switching a serial port to USB you turn off the RS-232 port at the same time. You can not use both USB com2 and RS232 com2 at the same time.

73 de mikel

2493
Hi, what is the main problem ? Wwith the K3 in CW and VOX no PTT signal is needed. If you do not want to use VOX and want PTT signal when using the internal keyer you just need to activate "PTT activated by keyer" under the keyer settings in the Radio-RRC.

73 de mike

2494
To configure the IC-7000 you should look in the ICOM in general chapter in the manual. It's like all other ICOM:s. The IC-706 chapter describes the IC-706 with separated control panel and it's not possible with the IC-7000.

73 de mike

2495
General discussion / Re: Exactly what is wrong!
« on: 2011-11-22, 20:26:13 »
We tested today with HRD and found that the creator of HRD has forgot to include the Power on command in FT-2000 mode. You can test to setup HRD in FT-950 mode then the FT-2000 will start up. Of course there will be other problems using it in FT-950 mode.

We will make a new setting where you can tell the RRC to send the "Pwr On" command automatically when you connect in mode 4.

73 de mike

2496
Hardware, Cabling, Installations / Re: No sound TX on PSK
« on: 2011-11-22, 18:14:06 »
You must describe what is not working. If you activate "Continuous RTP" in control end audio is always go from Control-RRC to Radio-RRC. You can test in SSB mode to activate VOX in the radio and shout in the Microphone. If the audio is not comming through the cabling are not OK. If the audio is there but the the transmission is cut in the tail you must change the connections so you PTT the Control-RRC, thats always better then the PTT will be in sync with the transmission.

73 de mike

2497
Hardware, Cabling, Installations / Re: No sound TX on PSK
« on: 2011-11-21, 19:10:47 »
Hi

If you use the software to send PTT commands via the CAT interface, the control RRC do not get the information about change to transmit mode. So you either need to connect to the PTT input of the COntrol-RRC or set "continous RTP" on to let the audio go from Control-RRC to Radio-RRC all the time.

73 de mike

2498
General discussion / Re: Exactly what is wrong!
« on: 2011-11-21, 19:06:12 »
Hi agn

It does not replace the cable, what i mean is that the system in this mode are not sending any messages created by it self or removing any messages sent by HRD for example. In the case with TS-480 the RRC switch on the the TS-480 if you have set it in the TS-480 mode (5) for using the control panel. Then we know there is a TS-480 connected and can handle it in  a separate way. If you set it up in mode 4 it will not know if there is a FT-2000 or a TS-480 connected and the on/off switching is up to the PC-software to handle. Of course there should be possible to make the firmware in the way you can select what radio you have connected and then send the switch on command automatically when the SIP-connection is up. But I don't know why HRD  don't do it with FT-2000 if does with other rigs ?

73 de mike

2499
General discussion / Re: Exactly what is wrong!
« on: 2011-11-21, 15:32:49 »
To make things clear, the RRC-Micro and the RRC  do not add, remove or interfere it just opens up a channel for the PC-progrsm like HRD to communicate with the radio. So itīs up to the software and the radio to handle this things

73 de mike

2500
General discussion / Re: alinco dx-sr8
« on: 2011-11-20, 20:17:24 »
Hi
Check the red straps first to see that they are in the right positions then with an ohmmeter to confirm that none of them are broken.

73 de mike

2501
Yes you can use an external keyer if you connect it as a straight key, The keyer should be activated anyway

73  de mike

2502
General discussion / Re: Exactly what is wrong!
« on: 2011-11-19, 16:29:39 »
First. I don't know why FT-2000 is not switched on and off by HRD, both FT-950 and FT-5000 that i have used is no problem and they use the same protocol, maybe someone who has the FT-2000 can tell.
About the other PC-softwares I think we have done what can be done in our end to make it work. At least some of them uses old serialport drivers which will not accept the virtual comports without replacing them with more modern ones. For the TRX-manager we have good hope because we are talking with the developer and both we and him know what he need to do, to make it work. The DF3CB program I have never heard about, maybe we can do something together if we get in contact with him. The softwares from Yaesu I do not think we can do anything about, we just have to wait and see if they comes with an update of some other reason. I don't know what you mean about being honest, we are saying that it works with HRD and we do our best to make it work with others also.  We have spending several hundreds of hours testing different approaches but when you can not do debuging from both ends it's very difficult. But we will continue to follow the different softwares, and if there is an opening we will do what we can to make it work.

73 de mike

2503
Hi

Is there still any problem ? Dont' you want the rig to start when you connect ?

/mike

2504
Configuration, RRC 1258 / Re: Version 2.46 Software -OUT1/2
« on: 2011-11-09, 13:58:24 »
Hi

There is no diffrnce in the firmware, it's only the manual which is adjusted, the pin numbering of the I/O connector was wrong.

73 de mike

2505
General discussion forum / Re: Antenna Switch/Rotator Contr.
« on: 2011-11-09, 11:08:07 »
The connection to the TS-480 and to the Prosistel are using the same serial port in the Webswitch but the protocols are totally different so it will not be possible to connect them in parallell

73 de mike

Pages: 1 ... 165 166 [167] 168 169 ... 201