Messages

16

Configuration, Webswitch 1216H / Re: 1216H at 4.2 Current Frequency

« on: 2014-08-28, 21:00:15 »

Yes, at the begin the good sensor runed in bus a and in bus b. When I have this sensor with the wire longer also it no runs.
Sorry, the second question I have no understood.
Franco

17

Configuration, Webswitch 1216H / Re: 1216H at 4.2 Current Frequency

« on: 2014-08-28, 16:58:26 »

Yes Jan, central wire to BUS and external wires to 0V.
I have another web switch with 2 sensors since 3 years and always works.
73 Franco

18

Configuration, Webswitch 1216H / Re: 1216H at 4.2 Current Frequency

« on: 2014-08-25, 16:05:21 »

Thank you Jan. I would like to put two temperature sensors on bus a and on bus b. I have tested 5 sensors DS18B20 but only one works.
At this good sensor I have puted a longer cable (because for external temperature) and now also it no works.
Can you help again? tnx 73 Franco

19

Configuration, Webswitch 1216H / 1216H at 4.2 Current Frequency

« on: 2014-08-21, 05:09:42 »

Hi, I have dayted a web wwitch 1216H (that I no use as automatic switch antennas) at the software 4.2. At the top now is writen "Current Frequency:0 KHz". What is this? Is possible to erase? In this version after the click mouse the signs ON OFF are later.
TNX, 73  Franco

20

General discussion forum / Re: web switch 10 relais and temperature sensors

« on: 2014-05-19, 07:50:25 »

Thank you Jan, 73
Franco

21

General discussion forum / web switch 10 relais and temperature sensors

« on: 2014-05-17, 10:22:22 »

Is possible to have 10 relays by two 1216H web switches (main and slave) and 2 temperature sensors?
Temperature sensors are connected in BUS A and in BUS B. The internal temperature sensor is connected in BUS A (connections 9 and 10) where there are the connections between 1216H main and 1216H slave. Is ok this parallele connection?
TNX, 73 Franco IK4ADE

22

General discussion forum / linear amplifier 1000JXX144

« on: 2013-07-03, 21:51:55 »

Anyone can to say to me how to remote vhf linear amplifier 1000JXX144 by RRC-1258MkII?
If I put  the same COM1 or COM2 configuration parameters and cables on RS232 as Expert 1K-FA is ok???
Thank you
Franco IK4ADE

23

General discussion forum / 2M Linear amplifier 1000 by I0JXX

« on: 2012-07-08, 11:56:52 »

Anyone have tested remotized 2m linear amplifier 1000 by I0JXX with remoterig?
73 Franco IK4ADE

24

General discussion / linear amplifier 1000jxx144

« on: 2012-07-01, 14:33:58 »

Anyone have tested the new 144MHz linear amplifier 1000jxx144 with remoterig?
73 Franco

25

General discussion forum / TS 480 + Expert 1K-FA + automatic antenna switch 1216H IS POSSIBLE?

« on: 2011-09-24, 22:59:25 »

I have cat circuit connected between TS 480 and linear amplifier Expert 1K-FA, so when I exchange band in TS480 also Expert followes. Is possible in the same time exchange also antennas to antenna  switch 1216H?  If is possible how can I to connect  TS480, Expert and 1216H by 1N4148 ?
Thank you. 73, Franco

26

General discussion forum / Re: Problems TS-480 and Expert 1K-FA

« on: 2011-09-24, 10:15:28 »

Now I have connected Expert 1K-FA (that is on air with TS 480) at the couple of TS2000 RRC and it works perfect.  So the problem of the linear amplifier is finished but the problem of TS480 is remained. 
TS480 every some minutes is muting, or no trasmits and I must turns off and turns on again for to continue a qso.
Anyone has my problem?
73, Franco

27

General discussion forum / Re: Problems TS-480 and Expert 1K-FA

« on: 2011-09-20, 16:09:22 »

Hi Mitch, I have not usb cable but only serial cable. 73 Franco

28

General discussion forum / Problems TS-480 and Expert 1K-FA

« on: 2011-09-19, 09:30:39 »

I use since 1 year 1 couple of RRC1258 MKII with TS-2000 (and RC 2000) for V-UHF, on COM 1 and COM 2 there are rotators and all is perfect.
I have also another couple of RRC1258 MKII with TS-480 for HF and on COM 2 a rotator Prosistel D with HRD. TS 480 no works so good as TS2000 system: Many times are latences, no listen more and stops; I must turn off the transceiver and turn on for regular functions.
Last week I have bought a linear amplifier Expert 1K-FA and I have connected it to COM1. The linear amplifier works well but every 2-10 minutes turns off, so I must close the TS480 and turn on it again for to return at the precedent good situation with 1K-FA opened. (NO rfi causes because this problem is also when I receive only).
Anyone can to help me? Thank you. Franco

29

General discussion / Re: new linear amplifier 2K-FA Expert SPE

« on: 2011-06-06, 09:59:02 »

Thank you Guy!

30

General discussion / new linear amplifier 2K-FA Expert SPE

« on: 2011-06-04, 07:40:44 »

Hello, the linear amplifier 2K-FA Expert SPE is in commerce. Anyone have tested it with RRC-1258 MKII? This linear amplifier has not RS232 db9 how 1K-FA but USB port. Anyone has tested with a converter RS232-USB? and what model?   73's  Franco