Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mitch

Pages: 1 [2] 3 4 ... 7
16
General discussion forum / Re: Icom 7300 and Remoterig
« on: 2022-12-28, 16:34:15 »
Hi Robin,

Still working the Kenwood 480 did not manage to configure Remoterig with the Icom 7300.

Have even tried Win4IcomSuite + RS-BA1 Version 2 to have both radio's at the Radio side  :'(

Looking for any info to work both radios.

73s Gary

17
General discussion forum / 480 will not connect
« on: 2022-12-01, 04:37:07 »
Can anyone help me out, I have now for the last three day's trying to turn on the Kenwood 480 radio and getting a problems.

Turning on I hear the bleep, face of radio will not light up and a small bleeping from face of radio. Have tried different power supplies and will not light up.

73 Gary

18
General discussion forum / Re: Icom 7300 and Remoterig
« on: 2022-11-06, 14:57:36 »
Had a look in the Chapter about ICOM IN General. Looking for the correct cables that are needed at Control side and Radio for the Icom-IC 7300.

Has anyone within the group managed to install the 7300 here and can provide cable info needed the run remote.

73's Gary

19
General discussion forum / Re: Icom 7300 and Remoterig
« on: 2022-10-27, 03:17:43 »
Thanks Mike,

Would you know what cable's I need from the Icom 7300 to RRC-1258MkII radio side.

And the cable needed again from the RRC-1258MkII to my laptop at the control side.

73

20
General discussion forum / Kenwood 480 problems
« on: 2022-10-02, 18:29:11 »
Can anyone help me out I can view both radio and control side and looks OK in both the browser for my Kenwood 480 HX.

For some reason over the last few days’ the radio face will not light up and hear a small clicking noise from speaker face.

Have tried changing all cable’s and also second Kenwood SAT face from my car to see if this could be the problem.

Has anyone else had this problem and know how to solve it.

73 Gary

21
General discussion forum / Re: Icom 7300 and Remoterig
« on: 2022-10-02, 12:16:31 »
Many Thanks,

Mike just need to try find the link to configuring  jumpers in each box.  I have RS-BA1 Version 2 and Win4IcomSuite would you know if this would work with PC at radio side + control side for the waterfall.

73s de Gary

22
General discussion forum / Icom 7300 and Remoterig
« on: 2022-10-02, 08:26:09 »
I have been working my Kenwood 480 for many years now with the RRC-1258MkIIs.

Would like to update the radio to my Icom 7300 would this be supported by Remoterig.

Have looked for post's in the Furum and can't see anyone that has got it to work for them.

73S

23
General discussion forum / RRC- With Yaesu FTDX3000
« on: 2021-03-29, 21:47:45 »
Can anyone help me out and tell me if possible or have installed both Yaesu FTDX-3000 like the Yaesu FT-450, FT-950, FT-2000, FT-5000 and FT-9000 shown in Yaesu Twin Concept Page.

Both FTDX-3000 are not supported as yet. I have managed to install radio at control side and second FTDX-3000 at the radio side. Looking for the correct cables that I need for radios and control side to work.


Not sure if I have the hardware configuration correct in both wiring of the jumpers installed in each RRC box at the control side and radio side below.


Regards,
Gary

24
General discussion forum / Re: Pairing RRC-1258 MKII
« on: 2021-02-28, 20:20:25 »
Hi Mike,

thank you for the quick response to my question.

Regards,
Gary

25
General discussion forum / Pairing RRC-1258 MKII
« on: 2021-02-28, 13:42:03 »
Hello there can anyone tell me is it possible to pair 2 RRC-1258 MKII control side tougher with radio side. I have pairs of RRC boxes the radio box is 5 miles from me.  The control is in my living room plus one in the bedroom.

Can you tell me if let a friend have the second box and his own Kenwood 480 would i be able to share the radio side at the same time when he is located over 400 miles from me and radio.

Kind Regards,
Gary

26
General discussion forum / Yaesu M-1 Base Microphone
« on: 2020-11-10, 13:21:16 »
Hello there can anyone tell me if they would know if the Yaesu M-1 Base Microphone is compatible with RRC-1258MkIIs.   have worked both the Yaesu MD-100A8X Yaesu MD-200A8X on the Kenwood 480 Sat with no problem but the M-1 does not key correct when I look at the green on the RRC-1258MkIIs control.

73 Gary

27
General discussion forum / RC-1216H Web-based remote control
« on: 2020-09-27, 02:13:44 »
RC-1216H Remote Control - Unused web-based remote control for ACOM-2000A, Expert Linears, KPA500, SteppIR never unused Pm only please.

Includes

-USB cable,
-Power cable

£180

For more information download the - Users manual

28
General discussion forum / Re: Acom 2000a install
« on: 2020-08-27, 05:01:10 »
Thanks Mike,

PM sent.

73 de Gary

29
General discussion forum / Re: Acom 2000a install
« on: 2020-08-24, 02:56:00 »
Hi Mike,

yes i cannot browse RC-1216 using the ddns hostname and only see via using the ip-address. 

I have checked the ddns server and can see on both domains. In System Info is showing this.

When i go to update my Own host name not found for .ddns.webswitch.se

========================================

Max available memory   18201
DNS status   Error, failed to resolve webswitch.se!
Dynamic DNS status   Error, code=103
Ping status (watchdog)   Unknown
Active profile   Default
Last WD Reset   5
TCP Error counter   0
Webserver   1

========================================

Last update: 2020-08-22 18:33:27

http://ddns.webswitch.se/status/resulthost.php
http://ddns.remoterig.com/status/resulthost.php

73 Gary

30
General discussion forum / Re: Acom 2000a install
« on: 2020-08-23, 13:44:53 »
Hi Mike,

before i could see the IP address at home and showing the subdomain for .ddns.webswitch.se link to control

73s Gary

Pages: 1 [2] 3 4 ... 7