Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - KD0PO

Pages: 1 [2]
16
It's not been possible before, but as Expert now a few weeks ago, have released a new firmware with protocol support, we will implement support for expert 1.3 and 2K as soon as we get a PA to test with

73 de mike

I also very much wish for control of my 2K-FA via RC-1216H.

I'd be happy to send you my amp to test with but I seem to use it several times a day!

Thank you for your top rate customer support.

Ray

17
General discussion forum / Re: RC-1216H
« on: 2015-12-03, 15:59:56 »
Mike and Jan,

thank you for the rapid response, the update firmware loaded without a problem.

Does the "script" line in advanced setting where I choose SteppIr remain blank?

I have to say, this is the best and most outstanding customer service I have ever received. I will be sure to mention that to anyone I talk to about remote rig.

Thank you for everything.

Ray

18
General discussion forum / Re: RC-1216H
« on: 2015-12-03, 03:39:19 »
here is the current system information:

Company Microbit
Product RC-1216H
Software 4.20
Hardware 3
Bootloader 1.12
Build Aug 28 2015 13:52:26
S/N 3015
PID 132
Uptime 0 Days, 0 Hours, 41 Mins, 47 Secs
======================================== 
MAC 00:1e:fd:00:c9:9f
IP address 192.168.75.236
Netmask 255.255.255.0
Gateway 192.168.75.1
DNS 192.168.75.1
========================================
Max available memory 18501
DNS status OK, remoterig.com = 213.180.92.20
Dynamic DNS status Inactive
Ping status (watchdog) Off
Active profile SteppIr DB-42
Last WD Reset 678052252
TCP Error counter 0

Advanced settings


Function type Prosistel D ACOM 2000A SteppIR Green Heron RT-21 DCU-1 Yaesu GS-232B AlfaSpid RAK Expert1K-FA KPA500   
Script/CSS/Image URL 
Enable external help pages No Yes   
Visually impaired support No Yes   

Serial settings


No settings available for this device

thanks
Ray

19
General discussion forum / RC-1216H
« on: 2015-12-03, 03:34:03 »
hello, I'm new to the forem and new to remote rig.
I took my RC 1216H remote control out of the shipping box and attempted to set it up for my SteppIr BD-42. I used setup manager v 1.28 to assign an IP and then used my browser (chrome) to find the RC and do the rest of the setup. Following the manual, I chose SteppIr from the advanced settings then clicked on "serial settings", I get the response "no settings available for this device" ???

So I thought maybe I needed to update the firmware, so I looked on the web page and that's when I really screwed up!

The RC-1216H said it had ver 4.21, I saw that the updates had various numbers from 4 to 4.5 to 4.12 to 4.20. I chose 4.20 as it had the newest date. I uploaded it to the device and all was well but still got the message "no settings....for this device". Ok, now what???

That's when I realized that there is a Web Switch Ham 1216H section and a RC 1216H section. I put the wrong device firmware in! I tried to put the last file in the RC-1216H list in but it will not load.... Perhapse because it has a number lower than 4.20 and has an older date?

 Is the a copy of RC-1216H v 4.21 or newer available? Have I created a fatal error?

 Is my box bad as the serial port can't be be programmed?

Yes, I'm lost haha...

thanks in advance for any and all help.

Ray

Pages: 1 [2]