Messages

16

General discussion forum / Re: KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-05, 17:50:07 »

Hi Willi
Thanks for reply.
Actually i have been reading the manual several times, on this subject.
I do know HRD can be used, i am also familiar with the ARCP from Kenwood.
But so far, i have not figured out from anywhere, how to set up HRD or the ARCP.
But i'l beleive i will :-)

73 Per

17

General discussion forum / KENWOOD TS-590 - HAM RADIO DELUXE

« on: 2017-05-04, 21:23:08 »

I am struggeling with the option to remote control my TS-590 over the internett, via Ham Radio Deluxe.
Setting up the both RRC is not complicated, but i'm not able to figure out how to set up Ham Radio Deluxe rig control, to  control the remote station.
anyone here who happends to know how???

Per LA4ESA

18

Hardware, Cabling, Installations / Re: TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-25, 10:46:58 »

Thanks again. I look forward to start the project when i receive cables from you and the xtra TS-590 will be picked up on wednesday.
Have a nice day.

Per/LA4ESA

19

Hardware, Cabling, Installations / Re: TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-25, 09:40:10 »

Thanks again for quick reply, but do i still need the RS232/USB with the FTDI chip??
So far i have not found the product in any store in Norway.

20

Hardware, Cabling, Installations / Re: TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-24, 18:32:48 »

Ok on that, thank you.
Cables are ordered from your webshop.
At the control end, i would like to read SWR etc through HamRadioDeluxe. I suppose i have to connect RRC control unit to my computer through the COM2 port on the RRC and then the COM1 port to the radio at the control end.
But, my computer does not have a RS232 COM port, only lots of USB ports.
Do you have any suggestions of the best RS232/USB cable to use???
Or can i use anyone at the nearest Kjell&co store?? with male RS232 to USB???

21

Hardware, Cabling, Installations / Re: TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-24, 14:24:17 »

Thanks, cables ordered.
Please comment if i have to change anything in the RRC units, by having a look at the following pasted from the control RRC:

Info on RRC:

Name   Value
Company   Microbit
Product   1258
PID   4
Version   7
HW   8
Software   2.90
Bootloader   1.10
Compiler   4.6.2
Build   Feb 17 2016 10:16:14
ROM/RAM   481192/44080
ETH-RAM   2944 (max 3kB)
USB-RAM   15352 (max 16kB)
Battery-RAM   4
ResetSrc   0 [3]
Last WD Reset   3582799757
Uptime   0 Days, 2 Hours, 59 Mins, 16 Secs
    
Serial number   6289
MAC address   00:1e:fd:01:8f:31
IP address   192.168.0.23
Netmask   255.255.255.0
Gateway   192.168.0.1
DNS   84.208.20.110
Wi-Fi network   not connected

22

Hardware, Cabling, Installations / Re: TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-24, 11:50:36 »

Thanks for your reply.
Could you please give me article number/name which gives me the possibillity to order from your webshop??

Per

23

Hardware, Cabling, Installations / TS-590S TWIN, WITH RRC-1258 MkII

« on: 2017-04-21, 11:31:30 »

I am concidering to by another Kenwood TS-590s, which means i will have one TS-590S at the radio end and one at the control end.
I do have the two boxes, RRC-1258 MkII.
I do also have the cables for running remotely ONE TS-590S.
The question is: can i use the same cables to run TS-590S in the TWIN solution??
The cables i have are called:
1258-K12A13A 75. Kenwood mic adapter cables
1258-CAT-2m  77. CAT cable 2m PC to RRC
1258-CAT-YK  79. Kenwood, Yaesu CAT cable K15c, Y6c. Radio RRC to Kenwood/Yaesu

24

General discussion forum / KENWOOD TS-570

« on: 2016-09-10, 17:00:44 »

Is it possible to use Kenwood TS-570 with the RRC units in both ends?
Or even better;  with TS-570 in radio end and TS-590S at the control end?

25

Configuration, RRC 1258 / Re: YAESU FT857 PTT NOT WORKING

« on: 2016-07-05, 16:08:42 »

Because i borrow the complete system fra a ham friend, he did not deliver the original mic in first place.
Today i got the MH31 mic and all seems to work nice now.
Next step is to place the radio at the cottage QTH and then test from home QTH.
I have done a lot of remote with TS-480 some years ago, but sold the system when mooving to a new adress. Then the noice level here have increased.
Trying again and hope it will be better. Not so much noice at the cottage QTH.
Thanks again.
73 de Per LA4ESA 

26

Configuration, RRC 1258 / Re: YAESU FT857 PTT NOT WORKING

« on: 2016-07-05, 11:40:14 »

Thanks for reply, then i beleive it's the mic. I'm using the remote controlled mic. All strappings are checked end checked again and i don't understand there can any mistakes on the strapping. Try to fix another mic.

27

Configuration, RRC 1258 / YAESU FT857 PTT NOT WORKING

« on: 2016-07-05, 10:08:32 »

Everything seems works nice in local network, as well in two different networks. But, the PTT does not work at all.
Either in local network or in two different networks.
Have tried several adjustings with jitteer buffer size and jitter delay, withour result.
The mic cable i made are tested and is ok. Nothing wrong with the mic, tested direct connected to radio, works nice.
The wiring inside both RRC are checked and tested with ohm meater, all ok.
Anyone with a good idea???

28

Configuration, RRC 1258 / Re: YAESU FT857 SWITCH ON/OFF

« on: 2016-07-04, 17:31:56 »

Well, now it seems to work properly.
I adjustet jitter buffer and jitter delay to default.
So far so good. Thanks for giving me new way of thinking. 

29

Configuration, RRC 1258 / Re: YAESU FT857 SWITCH ON/OFF

« on: 2016-07-04, 17:11:59 »

No, i did not, but i have now and it's still not working 
I'm very thankful for help 

30

General discussion forum / Re: RRC MICRO PC CLIENT

« on: 2016-07-04, 11:41:00 »

Thanks for your reply, i will configure this later on.
First i am testing the system with FT-857, but i'm not able to switch the radio on.
I have followed instruction manual in detail, use Dyn DNS everything ok at DDNS, but no sign of "life" at the raido end.
Do you happend to have any suggestion??