Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - HB9CVN-4F3CV

Pages: [1] 2
1
General discussion forum / Re: YAESU FTDX10
« on: 2022-03-28, 12:49:08 »
thank you for the replay.

That's the problem with the yaesu interface, which does not work in CW

2
General discussion forum / YAESU FTDX10
« on: 2022-03-22, 22:48:47 »
Hello,

searching the forum shows a couple of question about using remoterig for a Yaesu ftdx10, which are quite old and with no answer.

Did anyone managed to get that done? The solution provided by Yaesu has limited features and does not allow CW at all, so after a very positive experience with a Kenwood TS-480 I wonder if it would be possible to use remoterig.

3
Just in case somebody could be interested, the fault came from a bad solder of the optional TCXO unit.

Thanks again for helping.

4
I have connected the TS480 locally and the problem remains. After a short while, no audio, no frequency displayed and UL sent on CW.

According to the manual, it is on PIN 144 of the main microcomputer.

Couldn't find anything on google about that problem on the 480.

Definitely nothing wrong with the remotering set up


5
General discussion forum / multiple location
« on: 2020-10-14, 17:53:26 »
Hello,

I have a remote station with a TS-480 and run it with its front panel at home.

Now I would like to put the radio at the top of a mountain and us it together with a friend of mine.

Is it possible to have another remoterig box and another front panel and use the radio from two locations -obviously not at the same time-?

Would it be possible to run the second site with a remoterig box and a pc/software instead of using the TS-480 front panel?

As usual, I guess others have either already done that or at least enquired about it.

Thanks

6
first of all thanks to all of you for your help.

The radio is a TS-480SAT. It has been sitting for several months without being fired up. It sits in an office, so a controlled environment without any problem of humidity.

I am now resetting everything and will try again tomorrow. If it doesn't work and give me the same problem, I will first try the radio alone in local, not remote.

Obviously, if it still producing the same error it has nothing to do with the remoterig. This would not be a piece of good news, because it would mean that the radio would need repair.

7
I have reset both routers but it doesn't solve the problem.

When I switch on the system it works for about 15 - 20 seconds. Then no more audio and the frequency indication disappears.

I could try to change the port numbers but there is no logical though behind it, because I don't see anything which has been added which could be using a conflictual setting

8
hello,

I have tried to search the forum for the problem. Pretty sure, as usual, others have had the same and solved.


Had a system set up and running for more than a year without a single problem.

Then I was not using it -not switching the radio on- for 3 months.

Now if I switch the radio on, for a few seconds I can hear the audio and see the frequency. After about 5 seconds, the frequency indication dispappears and I see just dots, and I get a UL sent on CW.

Nothing has been changed on the remote side. Here the only change is that I have replaced one of the TV box attached to the network.

On the system status I see no error indication. Everything seems ok.

Anything I should do to locate the source of the problem.

Thank in advance for any help

9
General discussion forum / Re: connection problem
« on: 2019-08-25, 16:09:36 »
Hi Mitch,

I couldn't guess what the conflict is, as I have given an IP/port number to the control which is surely not used by anything else in the network.

Suddenly the problem disappeared... So hopefully it won't happen again

10
General discussion forum / connection problem
« on: 2019-08-24, 12:51:13 »
hello,

using a TS-480S remotely for several months now without any problem.

Yesterday it started with the following problem:

After a while, it could be a couple of minutes or just a few seconds, the frequency on the display disappears. I see a line of dots instead.

At this point it let me change the filter width, NR parameters, etc, but I get no audio and cannot transmit.

When it does that, it sends a CW "UL" message.

Any idea about what it could be?


11
General discussion forum / Re: IC-7100 noise from remoterig
« on: 2019-05-07, 16:54:45 »
found out that the problem is generated by a switching power supply I've used to supply the remoterig unit.

Using a conventional one made the problem disappear.

I have nil idea on how that could possible happen...

12
General discussion forum / IC-7100 noise from remoterig
« on: 2019-05-06, 23:40:30 »
hello,

just set up a IC-7100 with the remoterig. Serial 0300454 so used the additional board to be placed instead of the red strap at the control side.

The radio switches on but there is a tremendous noise, which increase if I turn any knob of the front panel.

I have tried to reduce the codec out gain as suggested in another discussion but the only result is that I have the overall volume reduced but with the very same noise.

www.youtube.com/watch?v=tK2icjQsMF4

Any suggestion on how possibly attack the problem?

Thanks in advance for any help


13
General discussion forum / Re: erratic CW
« on: 2019-04-21, 11:28:02 »
thank you

14
General discussion forum / erratic CW
« on: 2019-04-20, 08:30:18 »
hi,

been operating the remote station since yesterday.

everything seems to work but sometime the CW sends erratic signals.

The monitor is perfect but the signals sent are garbage. Lines get very long and erasing most points. Sometime it add points. Totally unreadable.

Same using the remoterig keyer or another electronic keyer through the I/O port.

Then after a while -about one hour- back to normal.

Any hints about where to start troubleshooting?

Internet connection is good.


Voice is ok.

15
General discussion forum / Re: TS-480 RFI - more information
« on: 2019-04-19, 21:17:16 »
uderstood. Will get a signallink or similar device

thanks Mike.

Pages: [1] 2