16
General discussion / Re: Virtual coms under Win 7
« on: 2016-05-25, 13:42:48 »
Seems OK. And correct baud rate too?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
General discussion / Re: Virtual coms under Win 7
« on: 2016-05-25, 13:29:08 »
A common problem is to not use the correct "RRC COMx" in RRC-Micro matching the radio RRC's serial port configuration. Are you sure you have configured that part correct?
18
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 22:02:13 »
No problem! Glad that you are up and running! 
19
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 16:41:06 »
Aha, the RRC is using its COM2 for the radio communication. Then you need to use the "RRC COM2" serial port, "Mode 4" in RRC-Micro, not "RRC COM0". Assign "RRC COM2" to one of the three Microbit Virtual Com ports you have(COM2, 3 or 4) and config PCC-2000 to use that com port.
20
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 15:59:58 »
Not using any resources is probably not a problem. You emailed Mike some screen dumps from the RRC and RRC-Micro settings before, but I did not see any "Serial Settings" screen dump from the radio RRC? That would show if the RRC-Micro configuration is matching the RRC's.
21
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 15:12:13 »
Aha, you was writing a new post while I was doing that too!
Do you see the virtual Com ports in Device Manager? (See an example in the attached picture)
Do you see the virtual Com ports in Device Manager? (See an example in the attached picture)
22
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 15:08:00 »
Steve,
I am not following what you mean
You started with saying that the installation failed and now you say that it worked? So now your (new) problem is with the use of the virtual COM ports?
I am not following what you mean
You started with saying that the installation failed and now you say that it worked? So now your (new) problem is with the use of the virtual COM ports?
23
General discussion forum / Re: TS-480HX won't power up
« on: 2016-05-24, 09:48:41 »
Powering the different devices can be done in any order, but obviously when attempting to connect the radio RRC/radio must be turned on(have power).
24
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 09:44:55 »
You also could include any logs found in the My Document's sub directory "MicrobitLogs".
25
General discussion / Re: ftsprapi.dll error in Win7Pro
« on: 2016-05-24, 09:41:20 »
Hi,
It seems the virtual com port installation fails and so ftsprapi.dll is not available when the ComOn program needs it.
Which version of RRC-Micro are you trying to install? Have you tried to run the installation as "Administrator"? (Not the same as your user account belonging to the Administrator group)
There should be a log file named either "MicroComInstall32.log" or "MicroComInstall64.log" in a sub directory to the installation folder called "drivers". If so then attach it for me to see,
/Jan
It seems the virtual com port installation fails and so ftsprapi.dll is not available when the ComOn program needs it.
Which version of RRC-Micro are you trying to install? Have you tried to run the installation as "Administrator"? (Not the same as your user account belonging to the Administrator group)
There should be a log file named either "MicroComInstall32.log" or "MicroComInstall64.log" in a sub directory to the installation folder called "drivers". If so then attach it for me to see,
/Jan
26
General discussion / Re: RRC-Micro 1.10 beta, 1274B 2 beta and RRC-1258 2.91 beta (CW support)
« on: 2016-05-23, 17:29:44 »
I have found what caused the error. It was a default value for the new Keyer settings that was invalid. You should be able to get the program running using this version:
http://www.remoterig.com/firmwares/RRCMicro_1.10.1.zip
(It was the "Weight" setting on the new "Keyer" tab that has a valid minimum value of 25, but was set to 20)
http://www.remoterig.com/firmwares/RRCMicro_1.10.1.zip
(It was the "Weight" setting on the new "Keyer" tab that has a valid minimum value of 25, but was set to 20)
27
General discussion / Re: RRC-Micro 1.10 beta, 1274B 2 beta and RRC-1258 2.91 beta (CW support)
« on: 2016-05-23, 09:06:36 »
Was it an upgrade or a clean installation you two did?
28
General discussion forum / Re: Common Network Settings
« on: 2016-05-20, 14:36:41 »
Yes means that regardless of which profile is selected the network settings are the same. No means that each profile has its own network settings. Yes was added to prevent accidentally change of network settings making the RRC inaccessible.
29
General / Re: A solid Nano app is worth $200 to me
« on: 2016-05-18, 21:07:48 »What is the status of the app update to fix the license check problem?What problems are you having? And have you tried the new beta versions?
30
General / Re: App Trial Period Has Expired
« on: 2016-05-12, 11:45:10 »
If you would like to help us improve the app there are new beta version available here:
http://www.remoterig.com/forum/index.php?topic=4688.0
http://www.remoterig.com/forum/index.php?topic=4688.0