Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sm3ccm

Pages: 1 [2]
16
Hi Paul.

I am using a Buffalo "High Power Ethernet Converter" on the control side.
Model: WL1-TX4-G54HP. It has four Ethernet Ports and I have the RRC and two
computers on it. Works great.

73 and HNY de Lars SM3CCM

17
Vid en sökning på forumet hittade jag nio olika call som alla har problem med den inbyggda keyern. Man kan inte lära gamla hundar att sitta och just nu känner jag mig som en sådan. Jag tränar idogt och det går sakta framåt så det kanske inte är helt hopplöst. 
En anledning att så få har hört av sig är nog att man använder en extern keyer med minnesfunktion. Det blir nog den väg jag kommer att välja.
Ett tips. Varför inte engagera någon av de jättefina CW-operatörer som finns i Luleå-området som "testpiloter", t.ex Janne, EKM, eller Peter, CEW. I övrigt tycker jag att RRC'na är en fantastisk produkt där ni är lyhörda för kunderna både när det gäller hård- och soft-vara. Tack för det.
God Jul och Gott Nytt de Lasse -CCM 

18
General discussion forum / Re: Feature request for webswitch
« on: 2010-12-18, 22:06:33 »
Another request. I would like to see the possibility to turn ALL relays OFF / ON
with one push button. de Lars SM3CCM

19
General discussion forum / Re: CW Keying
« on: 2010-12-18, 22:02:50 »
Thomas, DL7AV.
I do have exactly the same problem with the A2 keyer software as you have.
73 de Lars  SM3CCM

20
Jag kör omkring 80 procent CW ( sedan 1959 ) och har använt en hel del olika keyers men det är nästan omöjligt att komma överens med 1258'ans inbyggda. Mitt största problem är att jag tappar en kort i slutet av ett tecken. C blir K, R blir A o.s.v.
Jag tränar varje dag och det blir bättre och bättre hoppas jag.

Utan att ge honom någon förutfattad mening bad jag en kompis, f.d. telegrafist i handelsflottan, telegrafist på FN uppdrag, lång anställning på fast radio, att testa buggen. Efter 5 minuter gav han upp...

73 de Lasse

21
Konfiguration av RRC 1258 / Re: DYNDNS STATUS - V. 2.28
« on: 2010-12-16, 13:35:23 »
Per.

You dont need to reboot to get an updated status page. Go to info and back to status.
That will give you an updated status page.

73 de Lars

22
I have a Prositel PST71, the old type, with a 48VAC motor and a "C"-box.

HRD and "DX-lab > DXView" have only suport for the "D"-box. I can't change
controlbox as the "D"-box isn't compatible with the 48VAC model Prositel. 

Any hint how to solve the problem? Are there anyone that has source, in VB or old
fashion C, for a smal control program?

73 de Lars

23
General discussion forum / Re: Keyer is a little odd
« on: 2010-11-23, 12:25:12 »
I will try the 0.47uF cap and see what it does. However it shouldn't be difficult to look into the dropping dit case and see what see what the problem is, user, internet or program.
 

73 de Lars


24
General discussion forum / Re: Keyer is a little odd
« on: 2010-11-21, 10:20:09 »
I'm using a dual paddle and have the same problem. For me it looks like that there is a problem
with the dot and dash memories. C will often be a K, F will be a U a.s.o. Missing a dot after a dash before a word space. I don't have this problem with ICOM, AEA and MFJ keyers.

73 de Lars

25
General discussion forum / Tip for RRC to WiFi
« on: 2010-11-05, 14:52:40 »
At my Control site I have an ADSL 28Mb connection. To connect the router
to the shack I needed about 15 to 20 meter of Ethernet cable and also pass two
walls...

The solution was a "Buffalo Air Station High Power Ethernet Converter" model WLI-TX4-G54HP.

Working UFB and saved me a lot of cabling and work.

73 de Lars -CCM

 

26
Problem solved.

I, and probably the others, had missed that serial settings for COM2 on the Control RRC had to be changed from inactive to "logical parallel with COM0" (new from V.25). 

V2.26 working OK now.

73 de Lars -CCM

27
Went back to V2.25. Same thing - NO HRD connection.

Went back to V2.20. The IC756PRO connected straight away to HRD.
No problem what so ever... Something must have been changed??

73 de Lars

28
Same here.
Lost HRD connection with my IC756PRO when I installed V2.26.
73 de Lars

Pages: 1 [2]