16
General discussion forum / Re: New beta firmware available
« on: 2013-02-07, 21:53:55 »
Hello Jan, any other changes or only messages from this thread included?
regards
Chris
regards
Chris
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
General discussion forum / Re: New beta firmware available
« on: 2012-12-25, 20:39:15 »
Jan, actual firmware run well - 100% OK. I only update to Beta. i do not other changes or settings.
Will send you a URL and you can try a my station
But over all - enjoy holiday ( hope for you till end of January :-) - if not give me hint a i will talk to Mike.
best regards
Chris
Will send you a URL and you can try a my station
But over all - enjoy holiday ( hope for you till end of January :-) - if not give me hint a i will talk to Mike.
best regards
Chris
18
General discussion forum / Re: New beta firmware available
« on: 2012-12-24, 10:52:23 »
Hello Jan,
its a PST110 but i dont think that rotor is the problem.
At right side after the 2. pre select button is shown the 3. build grafik build up and! also the 360 degree scale at this place build up and never stop it. The page will be longer and longer.
If you like i can install again Beta version and try to make a screen shot or if you like i can send by PM you my URL for direct access to WebSwitch to test your self (you can test the beta here).
After i deinstall Beta and using latest version 2.x it runs well.
73 Chris
its a PST110 but i dont think that rotor is the problem.
At right side after the 2. pre select button is shown the 3. build grafik build up and! also the 360 degree scale at this place build up and never stop it. The page will be longer and longer.
If you like i can install again Beta version and try to make a screen shot or if you like i can send by PM you my URL for direct access to WebSwitch to test your self (you can test the beta here).
After i deinstall Beta and using latest version 2.x it runs well.
73 Chris
19
General discussion forum / Re: New beta firmware available
« on: 2012-12-21, 15:56:13 »
Here it looks like bug. Have select Rotator at left side menu; content page starts and grow up and up and... will dynamically longer and longer.
Must be at loading the 3. pre-select rotator button. First 2 buttons i can see
There is a LOOP !!!!
I know it's BETA
73 Chris
Must be at loading the 3. pre-select rotator button. First 2 buttons i can see
There is a LOOP !!!!
I know it's BETA
73 Chris
20
General discussion forum / Re: Rotor
« on: 2012-10-29, 06:45:31 »
Mike thanks.
I am a web programmer and it's easy to create this page - if you know what RRC or WebSwitch HTML pages exist's
And that only was the question: there a list with all for user available HTML pages and commands? Yes i can snif and also watch/see at button line what pages are used.
The :8003 is your local server where the "privat" pictures (www.xxx.net:8003/switch.egi) are stored?[why .egi? ]
73 Chris
I am a web programmer and it's easy to create this page - if you know what RRC or WebSwitch HTML pages exist's
And that only was the question: there a list with all for user available HTML pages and commands? Yes i can snif and also watch/see at button line what pages are used.
The :8003 is your local server where the "privat" pictures (www.xxx.net:8003/switch.egi) are stored?[why .egi? ]
73 Chris
21
General discussion forum / Re: Rotor
« on: 2012-10-25, 13:34:23 »
Easy questions - easy answer:
at given page (address see above) is no rotor command listed - but Mike use one and give a example; and it's very useful command for user.
I am not looking for hidden commands and not for company secrets; sniffing is not my job.
Thats all
at given page (address see above) is no rotor command listed - but Mike use one and give a example; and it's very useful command for user.
I am not looking for hidden commands and not for company secrets; sniffing is not my job.
Thats all
22
General discussion forum / Re: Rotor
« on: 2012-10-24, 18:01:16 »Any description file or pdf exist with all(!) possible HTML commands?
... found a page in web: http://www.webswitch.se/wp/?page_id=342 but i think more commands still exist
.... http://[Webswitch address]/rotator.htm
73 Chris
23
General discussion forum / Re: Rotor
« on: 2012-10-21, 13:39:50 »
...also it will be helpful if we can have "back" the 2 buttons CW and CCW - and if a Android App exit with Rotor function it will be a helpful tool in case of antenna repair work. Like a Rotor remote control.
73 Chris
73 Chris
24
General discussion forum / Re: Rotor
« on: 2012-10-14, 17:15:54 »
Mike, thanks info. I try rotor page, works as you told.
Temp sensors? Any plans? I think it's important if you runing some dB more then QRP
73 Chris
Temp sensors? Any plans? I think it's important if you runing some dB more then QRP
73 Chris
25
General discussion forum / Re: Rotor
« on: 2012-10-14, 10:47:05 »
...but these are static pages?
Example: if any Temp is changing you get info only after reload?
Example: if any Temp is changing you get info only after reload?
26
General discussion forum / Re: Rotor
« on: 2012-10-13, 10:31:57 »
Jan, thanks.
This page helps a big step further but also need:
- get actual position as a Value
- send a new postion as a HTML command
... also not so lucky for us (we have a very slow internet connection) is that every grafic is loaded from RemoteRig server.
Dont know in moment a real solution for that; own mini server or caching of all grafic or a flash (one time loaded and then not reloads needed)
73 Chris
This page helps a big step further but also need:
- get actual position as a Value
- send a new postion as a HTML command
... also not so lucky for us (we have a very slow internet connection) is that every grafic is loaded from RemoteRig server.
Dont know in moment a real solution for that; own mini server or caching of all grafic or a flash (one time loaded and then not reloads needed)
73 Chris
27
General discussion forum / Re: Rotor
« on: 2012-10-12, 12:18:51 »
...also a pur Rotor page for practical use is needed. Pur means all overhead of Webswitch page like all other menu points are not need (only in case of configuration/changes). If i operate with radio i need only rotor and his informations. All other config menu points normaly i dont need in practice.
73 Chris
73 Chris
28
General discussion forum / Re: Rotor
« on: 2012-10-11, 18:02:29 »
Jan,
- for a status page ( what is the actual position)
- the predefined Buttons for positions
Basic idea is to build a own page in HTML with all important info's: status of remote ip switches, different Temp sensors, position of rotor.....
.... a Housekeeping page...
Every solutions has his own Webpage; if they all in use - many windows are all the time open,a seconde PC-monitor is needed
Still only a idea;
73 Chris
- for a status page ( what is the actual position)
- the predefined Buttons for positions
Basic idea is to build a own page in HTML with all important info's: status of remote ip switches, different Temp sensors, position of rotor.....
.... a Housekeeping page...
Every solutions has his own Webpage; if they all in use - many windows are all the time open,a seconde PC-monitor is needed
Still only a idea;
73 Chris
29
General discussion forum / Rotor
« on: 2012-10-10, 20:30:58 »
There any plans to add function (- Reading/controlling via HTTP) for read/write position for rotor like the million function for NEXA ?
Idea is to build a HTML page with all status info like all used Temp sensors, actual position of rotor and so on
73 Chris
?Idea is to build a HTML page with all status info like all used Temp sensors, actual position of rotor and so on
73 Chris
30
General discussion forum / Re: any using V2.5 with success?
« on: 2012-06-11, 21:56:05 »
Jan, thanks for info.
And YES - a PDF will be fine. Actual online help is not real usefull and a liitle bit "hungry"
regards
Chris
And YES - a PDF will be fine. Actual online help is not real usefull and a liitle bit "hungry"
regards
Chris