Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ea3in

Pages: 1 2 [3] 4 5 6
31
General discussion / Re: RRC Client
« on: 2011-03-22, 10:46:22 »
No

Thanks

32
General discussion forum / RC-2000
« on: 2011-03-19, 10:01:08 »
Hello,

I am looking for a RC-2000 unit to use it with my TS-2000
Any idea about where to buy it inside the EU?

Anyone has a used one to sell it?

Regards


Marcel

33
General discussion / Re: RRC Client
« on: 2011-03-18, 18:05:03 »
32 bits

I mail is snt tou you with the debug file

34
General discussion / RRC Client
« on: 2011-03-18, 09:08:34 »
I have migrated to version 1.1.4

My PC is Windows 7

After the new setup, I open a connection to teh Radio RRC and it says SIP connected, but if I look at the RRC status it says idle (it should be connecting/transferring). Obviously I can't establish a HRD connection beacuse there is no a real connection.

I think the setup is ok

I have another laptop with an older RRC client and oit works ok, so no problem with the Radio RRC setup.

Any idea?




35
I have no answer from ACOM for the moment.

I will try again

Thanks

36
Thanks,

I will try to find here

Regards

37
Hello

I'm thinking on how to remote control my acom2000 amplifier.
I'm usng my remote TS-480 via the remoterig RRC's and I want to go one step further.

The idea is to be able to power it on and off and to go to control OPR/STB position.

Any advice or experience?

Regrads

marcel

38
I didn't found any better one than the stock MC-43

Also tried a Heil HC-4, an MC-60A and a senheiser.

39
Rude?

NOOOO, you right.

It was my mistake.

It is working now

40
I also tried to update the firmware using the setup manager utility. An error appears saying invalid file

I tried to re-load version 2.30.  diiferent error code: Wrong file type, got 144, expected 35

Info on the RRC is:

Company   Microbit
Product   1258
PID   0
Hardware   3
Software   2.30
Bootloader   <= 1.7
Compiler   4.1.2 (WinARM 4/2007)
Build   Dec 16 2010 14:37:11
ROM/RAM   343436/52960
ETH-RAM   2944 (max 3kB!)
ResetSrc   0 [3]
Uptime   113
    
Serial number   1548
MAC address   00:50:c2:11:8d:dc
IP address   192.168.0.227
Netmask   255.255.255.0
Gateway   192.168.1.1
DNS   213.27.248.53

41
Current firmware is 2.30

42
Sorry I miss the following

Yes, I am usin the wb interface

The downloaded file is:

http://www.remoterig.com/firmwares/RRC-1258-CRC_v2.32_2011-01-04.zip

43
The URl is

javascript:change_frames('update.htm','empty.htm')

I think I'm selecting application upgrade (as usual)

44
Can't upload formware 2.32
I get message: "Wrong file type, got 36, expected 35"
I have RCC's v1
Same behaviour in both the radio and control unit
I have downloaded the file twice.

Any idea?

HNY from Marcel, EA3IN

45
General discussion forum / Re: CW Keying
« on: 2010-12-18, 19:36:45 »
I am using Old type-squeece keyer option with lf delay = 500 ms and it is quite ok. No extra dits.500 ms was the solution in my case.
73s de Marcel

Pages: 1 2 [3] 4 5 6