Recent Posts

Pages: 1 ... 5 6 [7] 8 9 10
61
Hardware, Cabling, Installations / Re: CAT Interface for Kenwood TS480?
« Last post by dd0ul on 2024-02-15, 20:48:33 »
Moin Mike, thanks for your answer.

I found the chapter, thanks for the pointer :-)
 
An other question (I can't experiment because the TS480 is 400 km away :-) If I go there soon everything should be fine.

The instructions say I need a cable with 2x female plugs on the Radio side. That fits, there is a male plug on the TS480, as well as on the RRC-1258 Mk II

That's why I used to use a USB to 9 pin Sub-D adapter with a female plug. On the control RRC-1258, COM2 is also a socket (female). That means I need a different USB adapter or a gender changer, right?

vy73 de Micha, DD0UL

62
Hardware, Cabling, Installations / Re: CAT Interface for Kenwood TS480?
« Last post by sm2o on 2024-02-15, 12:10:23 »
Yes of course

Connect a cable from com2 to the radio CAT port

Look at the chapter, Kenwood in common for cable drawing

73 de mike
63
Hardware, Cabling, Installations / CAT Interface for Kenwood TS480?
« Last post by dd0ul on 2024-02-15, 12:02:10 »
Moin,

I'm able to use my remote TS480 (SSB, Digimode via VOX). What I miss: The CAT Interface. Is there any way to use the RRC-1258 MkII for this 2nd task?

vy 73 de Micha, DD0UL
64
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by sm2o on 2024-02-14, 08:05:44 »
Ja du måste bygla om för Icom in general också för mic, och 3.5 mm kabel för ljudet osv. Det är väl eg bara ic7100 , ts480 och K3 som är riktigt lämpliga att köra från appen

73 de Micke
65
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by SM7CKM on 2024-02-14, 07:56:32 »
Tack för svaret Micke. Jag satte fast frontpanelen på radion men det blev inget ljud i telefonen i alla fall, dessutom slutade bl.a. PTT att funka. Så det blir väl att leta efter en annan lämpligare modell av ICOM.

73'
Sven-Åke
66
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by sm2o on 2024-02-13, 21:37:13 »
IC-706 har ett mycket begränsat CI-V protokoll, det går det inte att ändra volymen via CI-V så panelen måste sitta på och man måste ställa in volymen i önskat läge på panelen

73 de micke
67
Allmänt diskussionsforum / RRC-Nano app
« Last post by SM7CKM on 2024-02-13, 15:45:00 »
Hej,
Använt RRC-1258MkII till min IC-706 i några år och det funkar utmärkt. Nu tänkte jag använda Nano-appen för att köra från en gammal Samsung Galaxy S4. Den kopplar upp helt ok och jag kan ändra frekvens, PTT etc MEN jag hör inget ljud bara ett mycket mycket svagt brus. Är det någon som har ett tips ?
73'
Sven-Åke
68
General discussion forum / Re: control unit not showing as control
« Last post by sm2o on 2024-02-12, 08:31:59 »
Hi

I have sent you instructions via mail

73 de mike
69
General discussion forum / control unit not showing as control
« Last post by WD0AJG on 2024-02-12, 06:48:11 »
I bought some used units.  The tags on them said serial number 9937 - radio unit and the other said 9940 control unit but when I hook up they both say they are a radio unit and both show serial 9937 although they do have different mac addresses
The control unit ( yes it has the cw knob, has a mac of :00:1E:FD:01:9D:71
The actual radio unit (no cw knob) has a mac of :00:23:a7:4f:ab:2d

How or can they be corrected?  I have tried reset several times but they still both come up 9937 a radio unit .

WD0AJG
70
General discussion / Re: Is RRC-Micro PC Client still available?
« Last post by sm2o on 2024-02-04, 17:31:57 »
Hi

The PC-client was discontinued some years ago

https://www.remoterig.com/wp/?page_id=28

73 de mike
Pages: 1 ... 5 6 [7] 8 9 10