706 startup not quite correct

[Mike/K3MMB]

Another NEWBIE needs a bit of help

Radio 706
1258s wired together works

connected to net with solid amber light on at AUX/MIC but unit does not power up? my setting below.
any assistance is greatly appreciated

73
mike

standard UDP ports
SIP 5061
DNYDNS seems to work
DHCP on control head - correct IP showing on other party at radio
fixed ip on radio

status display from control head
Name Value
Control panel OFF
Radio OFF
SIP status Connected/transfering
Last SIP error None
RTP Timeout 60
SIP Timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
External IP k3mmb.shacknet.nu
SIP Out port 5061
SIP In port 5061
Audio Out port 11000
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5061
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.1.228
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low

status from radio
Name Value
Radio OFF
SIP status Connected/transfering
Last SIP error None
RTP Timeout 60
SIP Timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
External IP 98.233.181.71
SIP Out port 5061
SIP In port 5061
Audio Out port 11000
Audio In port 11000
Command Out port 12000
Command In port 12000
External SIP In port 5061
External Audio In port 11000
External Cmd In port 12000
Other party 192.168.1.30
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low

[sm2o]

Hi

Have you set the Radio-RRC as DMZ server in the radio QTH router or made portforwarding for the ports 80,5061,11000,12000. Also check that you do NOT have anything called SIP ALG activated in the routers.

73 de mike

[Mike/K3MMB]

the radio-rrc is set to DMZ (192.162.1.228)
I have the 11000, 12000 and 5061 ports forwarded. There is no slots left for port 80 (my IRLP, wires node and a VZW network extender takes up the rest)
I am using a linksys WCG200 ver.2 cable modem/router
I do not see any ref to SIP ALG in the setup, but I do have vonage VOIP service.
DYNDNS seems to be working ok.

I have checked the straps and jumpers.  THe two RRC units seem to talk to each other over the net.

I do appreciate your help.
73
mike

[sm2o]

Hi

If it works locally, the strapping is OK and it's only a router issue. The only thing need to be changed in the Control-RRC is the SIP contact, replaced with the external IP or DynDns of the radio QTH router. I recommend you to change the webserver port of the Radio-RRC to 8000 so you can access the webserver remotely, if it works the other things should work also. Also check the firmware of the routers. Specially D-link routers need to have a quite new firmware if the DMZ or portforwarding should work OK.

/73 de mike

[Mike/K3MMB]

Still no joy.

I did notice that when I press the power button on the control head the SIP LED goes off.

I reset everything to default and still get the same result.

It has to be something simple, but I still can not see it.

73
mike

[Mike/K3MMB]

CORRECTED

Just tback of travel, and have the remote rig setup working.

The problem was simple over site and improper baud rate on COM0. Reset it to 19200 and things work like a champ.

73
mike