Author Topic: RRC-Micro CW macro problem  (Read 2844 times)

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
RRC-Micro CW macro problem
« on: 2015-10-30, 09:01:37 »
Setup:
1. RRC-Micro v1.8.0.0
2. Hardware dongle 1274B
3. Operating system Windows 7 Enterprise SP1 64-bit
4. At remote site RRC-1258 MkII with FW version 2.86 and K3 radio

Steps to reproduce the problem:
1. Open RRC-Micro client
2. Set up this CW macro: CFMUR5NN5NNDEOH1MLZTU
3. Other CW settings: speed 35 WPM, delay 50, weight 30
4. Send the macro: it works normally and color coding of sent message turns from yellow to blue in syncronization with sent CW
5. Close RRC-Micro by hitting the red disconnect button but do not close the client
6. Wait for few seconds
7. Push connect to reconnect
8. Send the macro: what happens is that color coding of sent message turns from yellow to blue NOT in syncronization with sent CW, actually much faster AND sent CW message on air is: CFMUR5NN5NNDEO1Z

roland

  • Guest
Re: RRC-Micro CW macro problem
« Reply #1 on: 2015-10-30, 10:26:39 »
Thanks for the report.
Will have a look at that

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #2 on: 2015-11-19, 09:46:19 »
Good to hear that. Looking forward for the new release. Could you also comment on feasibility of features from my wish list?
Juha

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #3 on: 2016-05-31, 08:26:33 »
Version 1.9.2.0 tried and it has the same problem.

Jan (Microbit)

  • Software Developer
  • Administrator
  • Hero Member
  • *****
  • Posts: 1796
    • View Profile
    • Email
Re: RRC-Micro CW macro problem
« Reply #4 on: 2016-05-31, 08:52:34 »
Version 1.9.2.0 tried and it has the same problem.
Radio RRC firmware version?
Always include type of hard/software and version when asking for support.

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #5 on: 2016-06-01, 17:31:09 »
2.86

Jan (Microbit)

  • Software Developer
  • Administrator
  • Hero Member
  • *****
  • Posts: 1796
    • View Profile
    • Email
Re: RRC-Micro CW macro problem
« Reply #6 on: 2016-06-02, 10:32:31 »
2.86
You could give 2.90 a try.
Always include type of hard/software and version when asking for support.

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #7 on: 2016-07-04, 09:18:27 »
I have now updated to 2.90 but the same problem is still there.

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #8 on: 2016-10-10, 09:42:34 »
New observation from today: when sending so much macros (like calling in pileup) that text screen below macro buttons becomes full, macros don't work properly anymore. Clearing text screen with clear button does not correct the problem and the client must be restarted. This is with version 1.9.2.0. All this restarting takes way too much time in a pileup.

OH1MLZ

  • Newbie
  • *
  • Posts: 23
    • View Profile
Re: RRC-Micro CW macro problem
« Reply #9 on: 2017-06-03, 13:29:40 »
This is still not solved..