Author Topic: Yeasu FT-857 No TX Audio  (Read 10409 times)

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Yeasu FT-857 No TX Audio
« on: 2017-04-15, 20:14:57 »
Hi everyone, I am currently setting up my remote station with a Yaesu FT857 and have purchased the dedicated RRC1258 mk2 kit including all connection cables and pre installed jumpers.
Everything appears to be working fine except I have no TX audio.  If I connect via LAN or via internet doesn't make any difference, the problem persists. 
 I have gone through all the settings on both units and can see no issues there.
 I have also tried it with the mic plugged directly into the radio instead of the control unit and TX audio then works fine.  I just wondered if anyone is familiar with this problem and could suggest how I might resolve the issue.
« Last Edit: 2017-04-19, 17:34:32 by GW6OVD »

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #1 on: 2017-04-15, 20:55:04 »
That type of problem is likely caused by the red straps on the socket in one or both of the RRC's.

I would open them up and double check to make sure that they match the manual for that rig and are making contact.

73,
Mitch DJ0QN / K7DX

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #2 on: 2017-04-15, 22:02:53 »
Hi Mitch, thanks for your reply, the units I have uses a  small, pre wired pcb installed where the straps would normally be fitted. both of these are snugly fitted into the sockets so I think the problem lies elsewhere.  I will however check for continuity between the appropriate pins in case a track is damaged. 73 Mal

dj0qn

  • Hero Member
  • *****
  • Posts: 2223
    • View Profile
    • DJ0QN / K7DX
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #3 on: 2017-04-15, 22:06:04 »
Hi Mal,

Are you 100% positive that the pcb is for the 857? I am not aware that one was even available for that rig. The other Yaesus are not compatible.

73,
Mitch DJ0QN  / K7DX

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #4 on: 2017-04-15, 22:26:01 »

The one I have is
 RRC-1258MkIIs v7 FT-857 is a package with hardware and software for the Yaesu FT-857.
The control cables are included and no strapping is needed, only IP-configurations etc.

As you can see from the description it should be more or less plug and play but I will double check the strapping pcb's (1258Y-3 Yaesu) tomorrow.
73 Mal 




« Last Edit: 2017-04-16, 11:04:57 by GW6OVD »

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #5 on: 2017-04-18, 09:51:07 »
Hi
Rre you using the standard microphone ? the remote control microphone MH59A8J can not be used.

73 de mike

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #6 on: 2017-04-18, 15:09:49 »
Hi Mike, thanks for your reply, apart from being wide banded the FT-857 is all standard including the MH31 mic.
73 Mal GW6OVD
I have connected both units to my local network now until I can resolve the issue.
Current settings

Control Status
Name   Value
Control panel   ON
Radio   ON
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(45)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
Current audio packet size   20
Current audio quality   2 - Linear 16 bits 8 kHz
SIP Out port   13000
SIP In port   13000
Audio Out port   13001
Audio In port   13001
Command Out port   13002
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   192.168.1.80
Input 0   High
Input 1   High
Input 2   High
Output 0   High
Output 1   Low
Output 2   Low
DNS status   OK, remoterig.com = 213.180.92.125
Active profile   Default
PTT status   OFF
Common network settings   Yes


Radio status
Name   Value
Radio   ON
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(45)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
Current audio packet size   20
Current audio quality   2 - Linear 16 bits 8 kHz
External IP   92.25.67.163
SIP Out port   13000
SIP In port   13000
Audio Out port   13001
Audio In port   13001
Command Out port   13002
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   192.168.1.79
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status   Unknown
Ping status (watchdog)   Off
DNS status   Querying status
Active profile   Default
PTT status   OFF
Antenna-Switch (IP)   not connected
Common network settings   No


RADIO SETTINGS (Control)
Program mode   15-Yaesu FT-857 8900
Sip password   

Sip contact   192.168.1.80
Auto connect   No
Audio quality    2 Linear 16bits 8khz
Audio left/right ch swap   No
Codec out gain    255
Codec inp gain    18
Codec inp HPF Hz   163
Codec inp preamp   Yes
COM0 baudrate   64000
COM0 data bits   8
COM0 stop bits   1
COM0 parity   0 - off
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0   No

RADIO SETTING
Program mode     15-Yaesu FT-857 8900
Sip password   •••••
Audio quality   2-Linear 16bits 8khz
Audio dual-rx   No
Codec out gain    255
Codec inp gain    0
Codec inp HPF Hz   163
Codec inp attenuation   No
COM0 baudrate   64000   
COM0 data bits   8
COM0 stop bits   1
COM0 parity   Off
COM0 Program mode 3 char timeout   2



« Last Edit: 2017-04-18, 17:36:28 by GW6OVD »

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #7 on: 2017-04-18, 21:39:31 »
You still need to remove some of the jumpers see manual, be sure that the pcb are turned correct also.

/mike

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #8 on: 2017-04-19, 17:26:37 »
Hi Mike, thanks for your reply.
I have today removed both strapping pcb's, checked for correct orientation and continuity and all is good.
I have also double checked all the jumpers and can see no issue there either.
Cat 5 cable from radio rrc to radio also been checked and another cable tried but no change.

Jumper configeration
Control              Radio
1   open             1   N/A
2   closed           2   N/A
3   closed           3   Closed
4   N/A               3   N/A
5   open             5   Open                         RRC1258 mk2  version 7  software 2.85

73   Mal   GW6OVD
« Last Edit: 2017-04-19, 17:49:43 by GW6OVD »

oz1rh

  • Full Member
  • ***
  • Posts: 106
    • View Profile
Re: Yeasu FT-857 No TX Audio
« Reply #9 on: 2017-04-20, 02:14:23 »
It is a long time since I had an 857, so just a guess: did you connect the microphone to the control head or the RRC? Page 157 of the manual says:

Control-RRC: The original microphone can be connected direct to the RRC AUX/MIC connector.

Radio-RRC:
Between the RRC AUX/MIC connector and the radios microphone jack you can connect the standard screened patch cable (CAT5 or CAT6) included in the FT-857 package.

73, Palle, OZ1RH.

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #10 on: 2017-04-20, 08:51:36 »
Yes I assume you have connected the Mic to the Control-RRC MIC/AUX jack, and the Patch cable from the Radio-RRC Mic/Aux jack to the Radio mic jack.

What happens when you press PTT ? is the radio keying ?, is RX-audio muted ?

73 de mike

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #11 on: 2017-04-20, 12:36:50 »
Thanks both for your replies.
The mic is connected to the RRC control Aux/Mic jack.
The cat 5 patch lead is connected from the radio RRC Aux/ Mic jack to the radio RJ45 jack.
Everything works as it should except for the lack of audio on the TX signal
When the PTT is pressed RX audio is muted control and radio end and the radio transmits a carrier but no audio
If I plug the mic directly into the radio RJ45 everything works including TX audio so the problem is not the microphone.

73 Mal GW6OVD  :(

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #12 on: 2017-04-20, 15:56:03 »
I have no other ideas. Do you have the radio-RRC public reachable over internet so I can try from here

73 de mike

GW6OVD

  • Newbie
  • *
  • Posts: 12
    • View Profile
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #13 on: 2017-04-21, 15:36:34 »
Hi Mike, thanks for your kind offer. Ill get everything set up over the weekend and install Team Viewer on my PC.
I know how difficult fault finding can be without direct access so maybe this is the best way forward.
73   Mal   GW6OVD
................................................................................................
Now all set up, please see your messages for password and contact number.
« Last Edit: 2017-04-23, 17:07:56 by GW6OVD »

sm2o

  • Administrator
  • Hero Member
  • *****
  • Posts: 3004
    • View Profile
    • sm2oan
    • Email
Re: Yeasu FT-857 No TX Audio
« Reply #14 on: 2017-04-24, 12:53:51 »
it's not possible to send emails or PM to you, probably the email you have registered at the forum is not in use any more

73 de mike