Author Topic: SSB TX issue on icom 706  (Read 823 times)

eb3am

  • Newbie
  • *
  • Posts: 1
    • View Profile
SSB TX issue on icom 706
« on: 2017-04-20, 11:38:57 »
Hello everyone
I've been setting up a remoterig an Icom 706 as explained in your website.

I made the relevant tests of cables and running through the local area network (LAN). The result has been satisfactory.

The problem is that from the remote location through the Internet does not work on the transmission SSB, FM transmission but does a proper audio.
The reception is correct at all times, latency is not appreciated.
The remote radio acts on an external tuner and It works perfectly.

I've tried various configurations of equipment, different sound qualities and have tried to increase the values ​​of jitter.

The router has been configured for each assigned ports and so I tested the DMZ option with the same results.

I also tried to locate the head to another internet connection, and the result is identical.

Connection where the radio is working through a wimax link (3Mb / s symmetric), and the head is 200km in an installation of fiber optics (1000dwn / 200up Mb / s).

What can I do?

I add the configuration export html page:

___________________________________

Info
Name   Value
Company   Microbit
Product   1258
PID   4
Version   7
HW   8
Software   2.90
Bootloader   1.10
Compiler   4.6.2
Build   Feb 17 2016 10:16:14
ROM/RAM   481192/44080
ETH-RAM   2944 (max 3kB)
USB-RAM   15352 (max 16kB)
Battery-RAM   4
ResetSrc   0 [3]
Last WD Reset   1177952693
Uptime   0 Days, 0 Hours, 7 Mins, 20 Secs
    
Serial number   *****
MAC address   00:*:*:*:*:*
IP address   192.168.2.100
Netmask   255.255.255.0
Gateway   192.168.2.1
DNS   8.8.8.8
Wi-Fi network   module not present
Settings
Unit ID (Banner)   EB3AM
DHCP   0
IP   192.168.2.100
Netmask   255.255.255.0
Gateway   192.168.2.1
Dns server   8.8.8.8
Eth-type   5
IP-interface   0
Web page user   ****
Web page pwd   ****
Web page user(saving)   ****
Web page pwd(saving)   ****
Program mode   2
Control panel   0
Sip password   ****
Sip contact(Radio RRC IP/hostname)   
Auto connect   0
Audio quality   0
Audio dual-rx   0
Audio left/right ch swap   0
Codec out gain   255
Codec inp gain   0
Codec inp HPF Hz   3
Codec inp preamp   1
Codec inp attenuation   0
COM0 baudrate   19200
COM0 data bits   8
COM0 stop bits   1
COM0 parity   0
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0   0
COM1 mode   0
COM1 baudrate   9600
COM1 data bits   8
COM1 stop bits   1
COM1 parity   0
COM1 rts/cts   0
COM1 terminator (hex)   00
Use USB Com Port as COM1   0
COM2 mode   0
COM2 baudrate   9600
COM2 data bits   8
COM2 stop bits   1
COM2 parity   0
COM2 terminator (hex)   00
Use USB Com Port as COM2   0
COM3(Extra) mode (USB-COMFSK)   10
UDP cmd port   13002
UDP audio port   13001
SIP port   13000
Web server port   80
Telnet server port   23
Rx jitter buffer size   4
Rx jitter delay   3
Audio packet size (ms)   20
RTP tx mode   0
Disable audio tones   0
Audio tones -db [70-0]   30
IP identification (morse)   0
Full duplex   0
PTT-off mute delay   0
IP Type-of-Service (dec)   0
Yaesu power-on/off   0
UDP antenna-switch port   13010
UDP cmd min-data-size   0
Use common network settings   0
Check interval   0
DDNS Host name   0
Own host name   
Username   
Password   
Enable   0
Speed wpm [0/10-40]   0
Iambic   1
Paddle reverse   0
Weight [25-40]   30
Side tone hz [0,300-1500]   800
Side tone -db [50-0]   20
Lf delay ms [0-500]   0
Key delay ms [0-250]   50
PTT activated by Keyer   0
PTT tail delay ms [0-999]   0
Speed pot min wpm [5-99]   10
Speed pot max wpm [5-99]   40
IN0 mode   0
OUT0 mode   0
OUT0 mode   0
OUT1 mode   0
OUT1 mode   0
OUT2 mode   1
OUT2 mode   1
USB RTS as PTT   0
USB DTR as CW   0
Enable ping watchdog   0
IP address to ping   192.168.2.1
Ping interval (seconds)   300
Startup delay (seconds)   300
Failure count to reboot   3
1: Name (SSID)   
1: Password (PSK)   
2: Name (SSID)   
2: Password (PSK)   
3: Name (SSID)   
3: Password (PSK)   
4: Name (SSID)   
4: Password (PSK)   
5: Name (SSID)   
5: Password (PSK)   
6: Name (SSID)   
6: Password (PSK)   
7: Name (SSID)   
7: Password (PSK)   
8: Name (SSID)   
8: Password (PSK)   







Status

Name   Value
P5.2   ON
Connection status   OK
SIP status   Connected/transfering
Last SIP error   None
RTP status   Excellent(60)
UDP cmd status   OK(28)
SIP command timeout   0
Rx Jitter buffer size   4
Rx Jitter delay   3
Dual Rx   0
Current audio packet size   20
Current audio quality   0 - alaw 8 kHz
External IP   87.*.*.*
SIP Out port   13000
SIP In port   13000
Audio Out port   43010
Audio In port   13001
Command Out port   25532
Command In port   13002
External SIP In port   13000
External Audio In port   13001
External Cmd In port   13002
Other party   91.*.*.*
Other party(mac)   00:*:*:*:*:*
Input 1   High
Input 2   High
Output 0   Low
Output 1   Low
Output 2   Low
Dynamic DNS status   Unknown
Ping status (watchdog)   Off
DNS status   OK, remoterig.com = 213.180.92.125
Active profile   Default
PTT status   OFF
Antenna-Switch (IP)   not connected
Common network settings   No
System messages   No





___________________________
73 and thanks!

EB3AM, Jordi from Catalonia.
« Last Edit: 2017-04-20, 11:57:12 by eb3am »