Recent Posts

1

General discussion forum / Re: Audio dropouts with Yaesu twins

« Last post by DL2MIJ on Today at 17:55:34 »

Thanks for your answer Mike !

I can't rule out that it's the PC.
What comes to my mind is, that i use 2 soundcard interfaces, local/remote.
maybe my miniPC can't handle it ?

vy73  Robert

2

General discussion forum / Re: Audio dropouts with Yaesu twins

« Last post by sm2o on Today at 17:17:13 »

Hi

Are you sure it's not related to the PC ?. I have to restart WSJT-X to get audio out every time my screensaver has been activated. PTT works but no audio. I read somewhere it's related nvidia graphic card driver .

73 demike

3

General discussion forum / Audio dropouts with Yaesu twins

« Last post by DL2MIJ on Today at 06:50:43 »

Thanks for reading !
The error has been on for a few days.
Sometimes only twice a day, sometimes every half hour.
Transmit signal is still there but without audio.
I have to restart the Radio and then it works again.
I have restarted the RRCs and router, application update was done but the error is still there.

I am using "audio quality" 7 maybe there is a better solution for FT8 ?


Please help

vy73 Bob DL2MIJ

4

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by k5tri on 2024-05-25, 22:10:24 »

OK, found the issue after the reset. For some reason I was still able to ping the old IP which means some other device grabbed it.

As usual, in 99% of the cases the problem sits in front of the keyboard. When I replaced my router and all WiFi APs, i reserved a block of
IPs in the DHCP server. The RemoteRig IP was outside of that block.

Tripple facepalm. Thanks for your swift support and help however.

73 Mike

5

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by sm2o on 2024-05-25, 21:48:40 »

press the reset button for 20 secs to do factory default reset

have you tried to browse from another PC or from a phone ?

/mike

6

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by k5tri on 2024-05-25, 21:45:10 »

I haven't done a factory default reset yet, only new firmware. How do I perform the factory reset?

Another thing to note, I had the radio running and when trying to connect to the webserver on the control unit the radio control head
freezes up and the unit reboots.

7

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by sm2o on 2024-05-25, 21:16:54 »

Hi
I don't think this this is a Remoterig issue, if you have done factory default reset and you get this result, the problem is probabaly somehwere else.
There is a telnet server also at port 23 but I don't see how it would help

73 de mike

8

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by k5tri on 2024-05-25, 21:07:34 »

After removal of USB cable, Setup Manager found the device and showed the correct address and Port 80.

When I clicked the Config button, the address field was empty and all other address fields had the same address including DNS.
Changed it to the correct values and saved to the device.
Still not able to connect with a browser. Is there a console via Telnet to access the unit?

9

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by sm2o on 2024-05-25, 20:27:48 »

Remove the USB cable and use the same tab and click on find device button to the right. then select the correct unit an click on the browse button


/mike

10

General discussion forum / Re: Can't connect via web browser to control unit

« Last post by k5tri on 2024-05-25, 20:18:43 »

See attached. This is what the Microbit Setup Manager presents.