1
Configuration, RRC 1258 / Re: Mono Audio on RRC1258MkII and K3/0
« on: 2016-03-15, 23:28:40 »
Thanks Mitch - money will fix the issue! 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Configuration, RRC 1258 / Mono Audio on RRC1258MkII and K3/0
« on: 2016-03-15, 13:34:41 »
Hi,
I have a K3 (no sub receiver) with 1258Mk2 RRC at the transmitter end and a K3/0 and Heil headset at the home end.
[My problem is that I only get audio on the left speaker of my headphones.
I have tried an number of different K3 settings to no avail. I spoke with Elecraft who suggested "Make sure in your RADIO RRC Box the Audio Dual RX setting should be set to NO. The K3 Remote must be set for Config Menu > SPKRS 1."
My problem is that I don't have any 'Audio Dual RX' option in my RRC1256Mk2 Radio setup. I looked at the most recent version manual in the Remote Rig site and that menu option is present, but not in my version (2010 vintage) with current firmware.
Are there hardware differences on the 1258Mk2s that prevent me from getting audio into both sides of the microphone or is it a software configuration issue?
73 de Chris Vk5CP
I have a K3 (no sub receiver) with 1258Mk2 RRC at the transmitter end and a K3/0 and Heil headset at the home end.
[My problem is that I only get audio on the left speaker of my headphones.
I have tried an number of different K3 settings to no avail. I spoke with Elecraft who suggested "Make sure in your RADIO RRC Box the Audio Dual RX setting should be set to NO. The K3 Remote must be set for Config Menu > SPKRS 1."
My problem is that I don't have any 'Audio Dual RX' option in my RRC1256Mk2 Radio setup. I looked at the most recent version manual in the Remote Rig site and that menu option is present, but not in my version (2010 vintage) with current firmware.
Are there hardware differences on the 1258Mk2s that prevent me from getting audio into both sides of the microphone or is it a software configuration issue?
73 de Chris Vk5CP
3
General discussion forum / Volume of Remote Rig error tones on TS480SAT
« on: 2011-02-20, 13:50:16 »When my TS480SAT remote head fails to connect I get a very loud alternating tone for about 4-5 seconds. The TS480 volume control does not control the volume of the error tone. Is there any way to reduce this volume? If I use the unit in a hotel and it fails to connect i dont want to wake up my neighbour!
73 de Chris Vk5CP
4
General discussion forum / Re: WANT TO USE IC 7000 FOR REMOTE PEDESTRIAN MOBILE
« on: 2011-02-20, 13:47:19 »
TS-480SAT is a good radio for remote rig. See my QRZ.com listing for information on my setup. 73 de vk5cp
5
General discussion forum / Re: For SteppIR users
« on: 2010-11-22, 12:32:16 »
Hi Daniel,
I am using a TS480 and am a SteppIR Vertical. I have a cable which goes from the rear of the TS480 directly to the SteppIR box, tracks the frequency perfectly. Not sure what I will do when I get the SteppIR yagi and the SDR100 box going though!.
chris vk5cp
I am using a TS480 and am a SteppIR Vertical. I have a cable which goes from the rear of the TS480 directly to the SteppIR box, tracks the frequency perfectly. Not sure what I will do when I get the SteppIR yagi and the SDR100 box going though!.
chris vk5cp
6
General discussion forum / Re: HELP - can't turn 706 on at all
« on: 2010-07-04, 14:32:07 »
Should I have a connect button on my Control status age lke the one on page 30 of the manual?
7
General discussion forum / Re: HELP - can't turn 706 on at all
« on: 2010-07-04, 14:17:24 »Some more information
Control Status
Name Value
Control panel OFF
Radio OFF
SIP status Idle
Last SIP error None
RTP Timeout 0
SIP Timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 0 High
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DynDns status Error
Radio Status
Name Value
Radio OFF
SIP status Idle
Last SIP error None
RTP Timeout 0
SIP Timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
SIP Out port 5060
SIP In port 5060
Audio Out port 0
Audio In port 0
Command Out port 0
Command In port 12000
External SIP In port 5060
External Audio In port 11000
External Cmd In port 12000
Other party 0.0.0.0
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
DynDns status Error
8
General discussion forum / Re: HELP - can't turn 706 on at all
« on: 2010-07-04, 14:15:09 »
Is it possible here is a hardware fault on the RRC?
Should I go back to the previous firmware version?
Can think of much else to do - surely it would work on a LAn without being connected to internet?
Should I go back to the previous firmware version?
Can think of much else to do - surely it would work on a LAn without being connected to internet?
9
General discussion forum / Re: HELP - can't turn 706 on at all
« on: 2010-07-04, 14:04:19 »
Thaks, I have turned off Comm1. When I cycle power to RRC's I get red LED on AUX/MIC (breifly), flashig green LED, then Solid green LED, then nothing - no amber LED.
SIP staus is IDLE, Radio is OFF.
Any more suggestions?
SIP staus is IDLE, Radio is OFF.
Any more suggestions?
10
General discussion forum / HELP - can't turn 706 on at all
« on: 2010-07-04, 12:26:53 »
Hi - I have an IC706 that I annot get to turn on. The cable tests OK with intalled with the joiner. I can turn the radio on and off and change frq etx, rx, etc
I have both RRC units behind the ruter for testing. I have configured as per manual. Com1 is CIV. When I plud control head and base unit it I get yellow LED on RRC, no red LED, green power light steady. I can browse both RRS, (radio is 192.68.1.228:8000 (also tried without the 8000.
PROBLEM- I can turn the radio on at all. Also tried with 703- same problem.
HELP I am getting quie frustrated!
vk5cp
I have both RRC units behind the ruter for testing. I have configured as per manual. Com1 is CIV. When I plud control head and base unit it I get yellow LED on RRC, no red LED, green power light steady. I can browse both RRS, (radio is 192.68.1.228:8000 (also tried without the 8000.
PROBLEM- I can turn the radio on at all. Also tried with 703- same problem.
HELP I am getting quie frustrated!
vk5cp
11
General discussion forum / Re: alpha 87A
« on: 2010-06-29, 13:40:39 »
The Alpha 87A will work fine over the com port. I have been able to turn my refurbished 87A off and on, change settings and monitor output etc via an RS232 over the internet.
73 de Chris VK5CP
73 de Chris VK5CP
12
General discussion forum / Re: Help with intial 703 setup
« on: 2010-06-29, 13:38:07 »
Thanks Mike,
I had tested the cable with an RJ45 joiner. I will check the jumpers and the settings (again).
73 Chris
I had tested the cable with an RJ45 joiner. I will check the jumpers and the settings (again).
73 Chris
13
General discussion forum / Help with intial 703 setup
« on: 2010-06-26, 15:29:39 »
Hi all,
I am a new Remote Rig User. I am using a 703. I have made up the cable and tested it OK. I am testing the setup on my LAN and have set the radio up as 192.168.228 and the control as 227. I can browse the radio and the control OK.
My issue is that the 703 wont switch on. The radio is set for 19200.
Do I need to set up port forwarding on the router if both the units are 'behind' the router? If not what should I check?
I want to get it working on my home network before I set it up at the remote shack.
73 vk5cp chris
I am a new Remote Rig User. I am using a 703. I have made up the cable and tested it OK. I am testing the setup on my LAN and have set the radio up as 192.168.228 and the control as 227. I can browse the radio and the control OK.
My issue is that the 703 wont switch on. The radio is set for 19200.
Do I need to set up port forwarding on the router if both the units are 'behind' the router? If not what should I check?
I want to get it working on my home network before I set it up at the remote shack.
73 vk5cp chris
Pages: [1]