Recent Posts

Pages: 1 ... 6 7 [8] 9 10
71
General discussion forum / WiFi board connection issue?
« Last post by K7FL on 2024-02-17, 09:39:11 »
Symptom:
Remote rig/K3/0 WiFi combination not connecting to the internet

Observations:
The Microbit utility does detect the SSID from my Verizon JetPack
JetPack connects to all other devices … just not the K3/0 & RRC
Confirmed I have the correct password for accessing the JetPack
JetPack display does not show a connection to the RRC (but does for all other devices)
Red LED on WiFi module is on solid
Green LED on RRC blinks for about 20 seconds and then solid

Other
This combination with the JetPack has work fine for years
Problem began upon arrival in France a few weeks ago. Radio, etc was transported in airplane cabin inside a clam shell equipment carrier. Not aware of any rough handling.
I have removed and reseated the WiFi card a few times.
Thorough internal inspection revealed nothing unplugged or loose.
I can ping my remote connection and the test packets are satisfactory returned.

Any ideas are welcome

Dennis, K7FL



72
Hardware, Cabling, Installations / Re: CAT Interface for Kenwood TS480?
« Last post by sm2o on 2024-02-15, 21:10:21 »
You cannot use USB at the radio side you have to make a cabe according to the drawing

/mike
73
Hardware, Cabling, Installations / Re: CAT Interface for Kenwood TS480?
« Last post by dd0ul on 2024-02-15, 20:48:33 »
Moin Mike, thanks for your answer.

I found the chapter, thanks for the pointer :-)
 
An other question (I can't experiment because the TS480 is 400 km away :-) If I go there soon everything should be fine.

The instructions say I need a cable with 2x female plugs on the Radio side. That fits, there is a male plug on the TS480, as well as on the RRC-1258 Mk II

That's why I used to use a USB to 9 pin Sub-D adapter with a female plug. On the control RRC-1258, COM2 is also a socket (female). That means I need a different USB adapter or a gender changer, right?

vy73 de Micha, DD0UL

74
Hardware, Cabling, Installations / Re: CAT Interface for Kenwood TS480?
« Last post by sm2o on 2024-02-15, 12:10:23 »
Yes of course

Connect a cable from com2 to the radio CAT port

Look at the chapter, Kenwood in common for cable drawing

73 de mike
75
Hardware, Cabling, Installations / CAT Interface for Kenwood TS480?
« Last post by dd0ul on 2024-02-15, 12:02:10 »
Moin,

I'm able to use my remote TS480 (SSB, Digimode via VOX). What I miss: The CAT Interface. Is there any way to use the RRC-1258 MkII for this 2nd task?

vy 73 de Micha, DD0UL
76
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by sm2o on 2024-02-14, 08:05:44 »
Ja du måste bygla om för Icom in general också för mic, och 3.5 mm kabel för ljudet osv. Det är väl eg bara ic7100 , ts480 och K3 som är riktigt lämpliga att köra från appen

73 de Micke
77
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by SM7CKM on 2024-02-14, 07:56:32 »
Tack för svaret Micke. Jag satte fast frontpanelen på radion men det blev inget ljud i telefonen i alla fall, dessutom slutade bl.a. PTT att funka. Så det blir väl att leta efter en annan lämpligare modell av ICOM.

73'
Sven-Åke
78
Allmänt diskussionsforum / Re: RRC-Nano app
« Last post by sm2o on 2024-02-13, 21:37:13 »
IC-706 har ett mycket begränsat CI-V protokoll, det går det inte att ändra volymen via CI-V så panelen måste sitta på och man måste ställa in volymen i önskat läge på panelen

73 de micke
79
Allmänt diskussionsforum / RRC-Nano app
« Last post by SM7CKM on 2024-02-13, 15:45:00 »
Hej,
Använt RRC-1258MkII till min IC-706 i några år och det funkar utmärkt. Nu tänkte jag använda Nano-appen för att köra från en gammal Samsung Galaxy S4. Den kopplar upp helt ok och jag kan ändra frekvens, PTT etc MEN jag hör inget ljud bara ett mycket mycket svagt brus. Är det någon som har ett tips ?
73'
Sven-Åke
80
General discussion forum / Re: control unit not showing as control
« Last post by sm2o on 2024-02-12, 08:31:59 »
Hi

I have sent you instructions via mail

73 de mike
Pages: 1 ... 6 7 [8] 9 10