Topics

1

Configuration, RRC 1258 / Remote Configuration for TS-480 Unsuccessful

« on: 2021-01-25, 03:57:53 »

Everything is working fine for my local network connection. Every time I configure it to connect remotely, I just can't connect to the radio unit. The main radio unit, has a fixed address and is configured for DMZ. I have been trying to troubleshoot for days what I'm doing wrong but to no avail. My configurations are as follow:

Control Head Unit

DHCP   1
IP   192.168.0.169
Netmask   255.255.255.0
Gateway   192.168.0.1
Dns server   192.168.0.1
Eth-type   5
IP-interface   0
Web page user   
Web page pwd   
Web page user(saving)   
Web page pwd(saving)   
Program mode   5
Control panel   1
Sip password   *******
Sip contact(Radio RRC IP/hostname)   p1scoimc.ddns.remoterig.com
Auto connect   0
Audio quality   2
Audio dual-rx   0
Audio left/right ch swap   0
Codec out gain   255
Codec inp gain   0
Codec inp HPF Hz   3
Codec inp preamp   1
Codec inp attenuation   0
COM0 baudrate   57600
COM0 data bits   8
COM0 stop bits   1
COM0 parity   0
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0   0
COM1 mode   0
COM1 baudrate   9600
COM1 data bits   8
COM1 stop bits   1
COM1 parity   0
COM1 rts/cts   0
COM1 terminator (hex)   00
Use USB Com Port as COM1   0
COM2 mode   0
COM2 baudrate   9600
COM2 data bits   8
COM2 stop bits   1
COM2 parity   0
COM2 terminator (hex)   00
Use USB Com Port as COM2   0
COM3(Extra) mode (USB-COMFSK)   10
UDP cmd port   13002
UDP audio port   13001
SIP port   13000
Web server port   80
Telnet server port   23
Rx jitter buffer size   4
Rx jitter delay   3
Audio packet size (ms)   20
RTP tx mode   0
Disable audio tones   0
Audio tones -db [70-0]   30
IP identification (morse)   0
Full duplex   0
PTT-off mute delay   0
IP Type-of-Service (dec)   0
Yaesu power-on/off   0
UDP antenna-switch port   13010
UDP cmd min-data-size   0
Use common network settings   0
Check interval   10
DDNS Host name   1

Radio Unit

DHCP   0
IP   192.168.0.169
Netmask   255.255.255.0
Gateway   192.168.0.1
Dns server   192.168.0.1
Eth-type   5
IP-interface   0
Web page user   
Web page pwd   
Web page user(saving)   
Web page pwd(saving)   
Program mode   5
Control panel   0
Sip password   ********
Sip contact(Radio RRC IP/hostname)   
Auto connect   0
Audio quality   2
Audio dual-rx   0
Audio left/right ch swap   0
Codec out gain   255
Codec inp gain   0
Codec inp HPF Hz   3
Codec inp preamp   1
Codec inp attenuation   0
COM0 baudrate   57600
COM0 data bits   8
COM0 stop bits   1
COM0 parity   0
COM0 Program mode 3 char timeout   2
Use USB Com Port as COM0   0
COM1 mode   0
COM1 baudrate   9600
COM1 data bits   8
COM1 stop bits   1
COM1 parity   0
COM1 rts/cts   0
COM1 terminator (hex)   00
Use USB Com Port as COM1   0
COM2 mode   0
COM2 baudrate   9600
COM2 data bits   8
COM2 stop bits   1
COM2 parity   0
COM2 terminator (hex)   00
Use USB Com Port as COM2   0
COM3(Extra) mode (USB-COMFSK)   10
UDP cmd port   13002
UDP audio port   13001
SIP port   13000
Web server port   80
Telnet server port   23
Rx jitter buffer size   4
Rx jitter delay   3
Audio packet size (ms)   20
RTP tx mode   0
Disable audio tones   0
Audio tones -db [70-0]   30
IP identification (morse)   0
Full duplex   0
PTT-off mute delay   0
IP Type-of-Service (dec)   0
Yaesu power-on/off   0
UDP antenna-switch port   13010
UDP cmd min-data-size   0
Use common network settings   0
Check interval   10
DDNS Host name   1
Own host name   p1scoimc.ddns.remoterig.com
Username   rrc1258-8286
Password   ********

2

General discussion forum / TS-480 control connected but no screen

« on: 2019-02-04, 03:10:54 »

I have the radio and the control in the same network. Port 13000 - 13003 is open. SIP ALG is off on the router. I even put the control side on DMZ. The system seems to be connected. The control side will beep once and the yellow light on the aux/mic are both solid yellow/orange. Status are both ok on both box but the control head is not turning on. If I connect the control to the radio directly and turn it on, it will turn on. I will connect the box in between after that and the status on tha radio side will show that it's on, but the control still wont turn on. I'm out of my wits on this one.

I have the system for a while now. It used to work in network and remotely before. I put my radio stuff away and now I'm setting it up and having this problem. Don't know if I damaged the RRC. I noticed that if I put the wifi module on the control box, it won't turn on. But if I put it on the radio box, it works. I'm thinking that something is wrong with the control box. Any help is surely appreciated.