Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sm2o

Pages: 1 ... 176 177 [178] 179 180 ... 201
2656
Allmänt diskussionsforum / Re: Problemer med Icom-706 MKIIG
« on: 2011-02-28, 13:20:35 »
Vad menar du med att inte control RRC startar, den verkar ju lysa hela tiden och den gula tänds ?

Menar du inte att IC-706 kontrollpanelen inte startar förrän du restartar din router ?

Det har jag ingen förklaring till i så fall, jag har hört att någon tidigare haft det problemet, vad har du för router ?

/micke

2657
Allmänt diskussionsforum / Re: Problemer med Icom-706 MKIIG
« on: 2011-02-28, 12:51:24 »
Min norska räcker inte till för att förstå vad du menar

/micke

2658
Allmänt diskussionsforum / Re: Problemer med Icom-706 MKIIG
« on: 2011-02-28, 08:58:47 »
Hej

Jag utgår ifrån att du testat med alla grejer på samma plats och det då fungerar?
Om det blir connected/transferring men inget display info och ljud när du flyttat radion så beror det på
antingen har du inte anslutit 12V till radion, men det troliga är att port 11000 och 12000 inte kommer igenom brandvägen
utan endast port 5060, där för kan uppkoppling ske men ljud och data kommer inte igenom och då slår radion av också (radio OFF)
så kolla dina portforwarding inställningar i routern på radiosidan eller ännu bättre aktivera DMZ server istället så funkar det alltid

73 de mikael


2659
General discussion forum / Re: Power LED Blinking
« on: 2011-02-27, 19:44:26 »
Green blinking indicates problems with DNS

probably you have entered wrong adress to dns server, but you are using a IP number

so it works but the RRC cannot get in conntact with the DNS server, you can check it on the status page also

73 de mike

2660
General discussion forum / Re: Can I use IC-R2500 with RRC1258 and remote control SW (e.g. Bonito RadioCom 6)?
« on: 2011-02-25, 08:55:16 »
Hi

It impossible to say in advance. It depends of how the software handles the serial ports

73 de mike

2661
General discussion forum / Re: Icom 706 sleep timer / auto power off
« on: 2011-02-21, 10:02:04 »
Hi

We don't see it as a big problem, and I don't know if it's even possible to solve

73 de mike

2662
General discussion forum / Re: Volume of Remote Rig error tones on TS480SAT
« on: 2011-02-20, 14:30:13 »
The volume of the error tone is the same as CW-side tone. So reducing the CW-sidetone  at the CW-settings will reduce the error tones also

73 de mike

2663
Hardware, Cabling, Installations / Re: TS-480, RRC, FSK via com1
« on: 2011-02-17, 08:32:56 »
Remember that the COM 1 do not have all pins connected, So I guess you need to have a Interface which is NOT powered from the serialports as most of the home made transistor interfaces are based on. Better build one with a MAX232 powered separately.

73 de mike

2664
Hardware, Cabling, Installations / Re: TS480 using PC instead of its control panel
« on: 2011-02-17, 08:27:51 »
Hi

I have not used the ARCP-480. But you do not write anything about a cable to the radio CÁT-port.
You must connect a RS-232 cable from the Radio-RRC COM2 to the Radio CAT port as the ARCP do not use the same protocol as the control panel. See instructions. You also have to set up COM 2 to Kenwood protocol in both RRC:s with the right baudrate settings. And 57600 is just bandwidth consuming, 19200 is enough

73 de mike

2665
General discussion forum / Re: RRC1258 and secure communications ...
« on: 2011-02-12, 20:53:55 »
Almost all routers can be setup to create a VPN tunnel between two routers often using IPSEC, so it's no problem to build a secured setup.

But why bother if it's used for ham radio all audio will be sent out over the air for everyone to listen to ?

73 de mike

2666
General discussion forum / Re: Mic selection--Heil Goldline
« on: 2011-02-11, 23:31:30 »
Why don't you have the preamp on ?

Heil mics normally have lower levels than orginal microphone so start with preamp on and codec inp gain 18 when testing, Then increase mic gain on the radio. If you do not get enough you could increase the codec inp gain as last step.

73 de mike

2667
News / New software for the RRC-Micro PC client released (v1.1.2)
« on: 2011-02-05, 14:35:01 »
- Some minor cosmetic changes.
- Better handling of some error situations.

2668
General discussion forum / Re: SIP ALG activated
« on: 2011-02-04, 23:13:52 »
Hi

You can always try to change SIP port from port 5060 to something else. Try 8000.

If it does not help you probably have to change to a router which you can configure by your self.

If my ISP would not allow me to manage my router I should have changed ISP.

73 de mike

2669
General discussion forum / Re: IC706
« on: 2011-02-01, 18:28:29 »
Yes

You must select which output you will use for the keying signal. It's done under the I/O settings in the Radio-RRC

73 de mike

2670
News / New software for the RRC-Micro PC client released (v1.1.1)
« on: 2011-01-30, 17:42:04 »
- Now with profiles to make it easier to change between different setups.
- Now it's possible to use other microphones. Not locked to 1274A anymore. 1274A must be connected
  as PTT and licence dongle.
- User interface modified.
- Selectable packet size 20/40 ms. Follows automatically in RRC end.
- The Program window now follows windows standard and is NOT always on top.
- Some other small fixes also.
- Note! You must upgrade RRC to 2.33 at the same time.

http://www.remoterig.com/en/rrc_pc_client_sw.htm

Pages: 1 ... 176 177 [178] 179 180 ... 201