Messages

2401

Hardware, Cabling, Installations / Re: Blinking light on power indicator

« on: 2012-02-24, 00:57:41 »

Hi

750k/250k should be enough if it really is 250k but you can set audio quality to 0 to check if it's the problem. But first the PWR LED should not blink.  I guess you have NOT set dns IP OK, in most cases it should be the same as Gateway IP but not always. Check on the status page, what it says about dns status.

73 de mike

2402

General discussion forum / Re: Problem using Kenwood TS2000X & RRC-2000

« on: 2012-02-23, 18:50:58 »

What happens when you press the pwr on button ?  the yellow LED at the AUX/MIC jack should light up.
The setup for the TS-2000 is very simple so it can only be a cable or settings issue. You can email me the exported settings files if you want so I can check your settings.

73 de mike

2403

General discussion forum / Re: Cmd Latency, delay to start.

« on: 2012-02-19, 12:20:15 »

You are not describing what equipment or internet connection you are using. But there is no delay in sending the meesage over the Internet from the RRC, it's done as soon as the end of message character is received.

But with some mobile eg 3G connections we got reports that the beginning of the audiostream was missing or messed up. Those who had problem thougt that it took awile before the mobile network started to send a continuous stream of packets.  We introduced the possibility to send continuous audiostreams in both directions and the problem was solved.

Maybe you have the same situation for the command stream, but it's not that easy to send dummy data packets over the link to keep the bandwidth constant.

73 de mike

2404

Hardware, Cabling, Installations / Re: KN-Q10 USB control

« on: 2012-02-18, 14:51:20 »

No. USB is very difficult to transfer over the Internet. There are USB over Ethernet link equipment but I haven't heard about any which works reliable over the Internet.

73 de mike

2405

General discussion forum / Re: Control end wont boot when IN0 is active

« on: 2012-02-18, 09:42:16 »

IN 0 is not allowed to be low at power up. That's the same in all hardware versions and is not possible to change with software.

The bootloader is no involved in how the webpages looks like. It's only used to start up the main program, flashing new firwares etc. We not yet done any modifications to the bootloader that makes it necessary yo upgrade it from the orginally installed versions.

73 de mike

2406

Configuration, RRC 1258 / Re: No connection with ddns

« on: 2012-02-13, 16:18:24 »

I do not think the disconnection has anything to do with the RRC.s or the ddns. it's probably a network/internet issue.

Install pingplotter www.pingplotter.com and run it against your radio-qth, then you will see if the network connection is down when you got the disconections.

73 de mike

2407

General discussion forum / Re: FSK

« on: 2012-02-12, 20:45:44 »

Hi

The easisest way is just to split the audio from the 3.5 speaker jack. Thats how I do my self I use the signalink USB.
It also possible to connect a cable from the signalink to the TTL jack where audio is present between pin 1 and 6

73 de mike

2408

Hardware, Cabling, Installations / Re: Yaesu 857

« on: 2012-02-10, 17:55:40 »

Hi

I have attached an idea to cables which can be used if you do not want to do any mods on the pcb. pse try.

There will be boxes which can be used without mods in the future.

73 de mike

2409

General discussion forum / Re: Incorrect temp display in 1216E

« on: 2012-02-10, 17:14:46 »

Ok

It's not many days per year the temp is between 0 and -1 here and I might not have checked those days as I do not log the temperatures. We will check if there is done some improvements between 1.01 and 1.07

73 de mike

2410

General discussion forum / Re: Incorrect temp display in 1216E

« on: 2012-02-10, 16:41:35 »

Hi

I use four 1216E for temperature control my self and I have never found any problem with them, they show outdoor temps below zero now, all of them. It's firmware version 1.07 in them.

73 de mike

2411

General discussion forum / Re: Work Web Switch with ProSisTel PST110?

« on: 2012-02-08, 08:55:24 »

If it works or not are not depending on the Rotator. It's depending on the computer protocol which the Controlbox uses. As far as I can see it's the same D-box protocol as for the other Prosistel.

73 de mike

2412

General discussion / Re: FSK

« on: 2012-02-08, 08:25:03 »

Hi

No it's not possible. There is no such plans for the moment either.

73 de mike

2413

Hardware, Cabling, Installations / Re: Yaesu 857

« on: 2012-02-07, 12:23:07 »

Hi

It's possible, but the porposed mods takes less than 5 minutes. So we concidered it to be much more complicated to make splited cables. If you do don't forget the screeing of the mic wire on the radio side.

73 de mike

2414

General discussion forum / Re: VOX setting and CW on the TS-480

« on: 2012-02-04, 18:07:17 »

The Remotrig system does not know anything about the TS-480 settings, it always transfer the CW-keying signal to the radio. Then it's up to the TS-480 to decide what to do with it.

73 de mike

2415

Configuration, RRC 1258 / Re: Dynamic DNS Status: Error Code 9

« on: 2012-02-02, 22:55:38 »

Yes then the DDNS address is OK but the DNS adress on the IP-settings page is wrong. The RRC can not contact the same DNS as your PC. Check what DNS the PC use and set the same into the DNS address field in the RRC.

ddns and DNS is not the same thing

73 de mike