Remote Rig
RRC 1258 Support in English => General discussion forum => Topic started by: SV8PKJ on 2014-03-15, 18:35:24
-
Hello
I would like to ask you about a problem i experience with my Radio unit and RRC-1258MkII.
It had been working properly for the last two months .But,lately, whenever i turn on the apparatus the ethernet button stays orange preventing any access to the internet.
-
Please look at the messages in the status section of the RRC's web page and let us know
what it says.
Have you rebooted both RRC's to see if that solves your problem? It does in 95% of
cases I have seen where it just stops working for no reason.
73,
Mitch DJ0QN / K7DX
-
Check ddns status:
User rrc1258-5863
Host Name
IP Address 5.203.144.86
Last update 2013-12-22 14:38:14
Update count 9
rebooted I did but the problem remains...
73
SV8PKJ
-
That is the wrong status. I mean the status of the RRC connection under the menu "status"
on the top left. Please give us both RRC's status after an attempted connect.
You rebooted both RRC's, I assume?
73,
Mitch DJ0QN / K7DX
-
Yes the yellow LED at the Ethernet connector only says it's connect t a switch at 100 MBit/s it's nothing strange with that
73 de mike
-
turn on the apparatus the ethernet button stays orange preventing any access to the internet.
-
Not a clue what it is you are trying to say. Since you were able to give us your DynamicDNS settings
before, you obviously have network connectivity. It would be great if you would give the status for
the RRC's.
73,
Mitch DJ0QN / K7DX
-
I will try to describe my problem again.
My system was working ok for about 2 months. I would like to try some changes and unplugged the remoterig and I have it in my shack now.
I have both remoterigs plugged in my local network. I have both connected in my router. I can access the control remoterig but not the radio remoterig.
When I plug only the power jack in the radio remoterig, the ethernet jack lights on without to have an ethernet cable plugged in. Is this normal? I don't think it is...
When I try to connect with radio remoterig, the web page does not load at all. So no access to see the status, etc.
When I connect an ethernet cable, the light in the router's port does not light on.
I reset my remoterig in default but I have the same results.
I tried also a different ethernet cable.
Any other ideas?
Is there a service?
73
SV8PKJ
-
Hi
If the LED lights up even if you have not connected the LAN cable it's not normal. Probably the Ethernet interface has suffered a lightning storm and has been broken. The Ethernet Interface is not repairable, but if you send me a email i will give you a a good price for a replacement PCB
73 de micke
-
Have you tried to connect the RRC via USB and use the Setup Manager program to see the IP settings etc?
-
I have no problem with IP settings etc.
My problem is When I connect an ethernet cable, the light in the router's port does not light on.
The ethernet port is dead at RRC
-
I have no problem with IP settings etc.
My problem is When I connect an ethernet cable, the light in the router's port does not light on.
The ethernet port is dead at RRC
OK. Then it seems what sm2o/micke said is valid in your case.
-
Hi
If the LED lights up even if you have not connected the LAN cable it's not normal. Probably the Ethernet interface has suffered a lightning storm and has been broken. The Ethernet Interface is not repairable, but if you send me a email i will give you a a good price for a replacement PCB
73 de micke
Hi
I would like to ask how much will it cost me a new RRC?
thanks.
SV8PKJ@GMAIL.COM
73
SV8PKJ