Remote Rig
RRC 1258 Support in English => Configuration, RRC 1258 => Topic started by: sv1oz on 2014-03-23, 09:11:54
-
I used to have ICOM IC-706 as remote and latest I decided to to use V71 for V-U remote.
I changed jumpers on both RRC's and I downloaded latest SW 2.78
I made new cables for the radio and panel and I checked all of them with my multimeter were ok.
I selected Radio V71 and baudrate 57600 and connected both units in my local network to test.
On Rado RRC I put for sip 192.168.1.228:8080 and tried to turn on
Doesn't work. Pressing ON, on radio nothing happens . Not even a strange sound I had before with IC-706 when network was off.
I can see both RRC's to my computer via network if I put the addresses
I tried in panel RRC auto connect ON .then after reboot both RRC's had yellow led on and a beep came from speaker but no display...
In radio status now is
Radio ON
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(36)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
External IP 85.72.223.192
SIP Out port 5062
SIP In port 5062
Audio Out port 11000
Audio In port 11000
Command Out port 12200
Command In port 12200
External SIP In port 5062
External Audio In port 11000
External Cmd In port 12200
Other party 192.168.1.227
Input 1 High
Input 2 High
Output 0 Low
Output 1 Low
Output 2 Low
Dynamic DNS status OK
Ping status (watchdog) Off
DNS status OK, remoterig.com = 193.202.110.185
Active profile: Default
PTT status: OFF
Antenna-Switch (IP) not connected
and in panel status...
Control panel ON
Radio OFF
Connection status OK
SIP status Connected/transfering
Last SIP error None
RTP status Excellent(60)
UDP cmd status OK(44)
SIP command timeout 0
Rx Jitter buffer size 4
Rx Jitter delay 3
Dual Rx 0
Current audio packet size 20
Current audio quality 2 - Linear 16 bits 8 kHz
SIP Out port 5062
SIP In port 5062
Audio Out port 11000
Audio In port 11000
Command Out port 12200
Command In port 12200
External SIP In port 5062
External Audio In port 11000
External Cmd In port 12200
Other party 192.168.1.228
Input 0 High
Input 1 High
Input 2 High
Output 0 High
Output 1 Low
Output 2 Low
DNS status OK, remoterig.com = 193.202.110.185
Active profile: Default
PTT status: OFF
The RRC's are connected but no display or any control
On - off power on rig still do nothing
Looks like something wrong with setup?
Any I idea what I can check?
Dimitris
-
Probably the cables or the settings which are wrong. No red straps needed to make it work, they are only for the mic. Be aware that there is schematics both for TM-D710 and V71 in the same chapter and they are not the same
73 de mike
-
I double checked both cables in radio and panel RRC for connectivity or short and look correct as the diagrams in manual.
In settings I have selected program mode 5 (Kenwood TM- V71) in both RRC's and 57600 baudrate.
Radio settings
Program mode 5
Sip password
Sip contact 192.168.1.228:8080
Auto connect no
Audio quality 2
Codec out gain 255
Codec inp gain 18
Codec inp HPF Hz 163
Codec inp preamp yes
COM0 baudrate 57600
COM0 data bits 8
COM0 stop bits 1
COM0 parity 0-off
COM0 Program mode 3 char timeout 2
Use USB Com Port as COM0 no
Still not working.
Again if I select auto connect the units are connected without any further controls or display.
Dimitris
-
There is no port number in the SIP contact! Take the ":8080" out!
73,
Mitch DJ0QN / K7DX
-
Ok Mitch,
My mistake, but I removed extension port number and still not working with power on button of V71.
I am wondering why the units are connected when I switch to "Auto connect" ? (Status on radio site then shows connected) and in panel shows (No radio)
Does it mean that cabling is ok but some parameter is bad?
I really dont know what to check. First time I face such difficulty to make a radio work with remote Rig hi hi.
Any idea what to look next?
73 Dimitris
-
Hi
Auto connect should not be used
You can email me exported settings html from both units so I can take a look at them
73 de mike
-
Ok Mike thank U
I sent U the email
73 de
Dimitris SV1OZ
-
I finally found the problem at AUX/MIC red wires at control RRC.
PWR (5V) was one pin misplaced as a result the remote was not working
Mike helped me a lot by emailing me several suggestions about where to look for this issue.
I appreciate Mike for your kind support
All now is working as it should
73's to all
Dimitris SV1OZ