Remote Rig

RRC-Micro PC Client in English => General discussion => Topic started by: OH1MTS on 2013-01-31, 10:03:23

Title: Win7Pro 64
Post by: OH1MTS on 2013-01-31, 10:03:23
Updated to 1.6.3 and all ports disappeared even the installation says it configuring virtual 64bit coms.
Have removed all incl, Setup man. reinstalled but no ports.

I just get on launch "Error:Object reference not set to and instance of object"
Title: Re: Win7Pro 64
Post by: roland on 2013-01-31, 14:39:23
Not quite sure by the description whats going on there.
I could take a look at it with TeamView. I'll send you a private mail about that
Title: Re: Win7Pro 64
Post by: roland on 2013-02-01, 16:36:22
Just for your information. The problem was solved.
Title: Re: Win7Pro 64
Post by: OH1MTS on 2013-02-01, 18:51:06
YES!!! Thanks Roland for your countless hours helping my Dell (hell)
Title: Re: Win7Pro 64
Post by: roland on 2013-02-01, 19:39:28
Thank's man. It was a pleasure   ;D
Title: Re: Win7Pro 64
Post by: OH1MTS on 2013-02-04, 09:32:46
At Arlanda SAS lounge on my way to Moscow and IT WRKS!!!!!!
Title: Re: Win7Pro 64
Post by: Jan (Microbit) on 2013-02-05, 09:40:57
Quote from: OH1MTS on 2013-02-04, 09:32:46
At Arlanda SAS lounge on my way to Moscow and IT WRKS!!!!!!
;D
Title: Re: Win7Pro 64
Post by: OH1MTS on 2013-02-05, 19:13:59
Well again if I would be the smily user I would put all the positive ones X10 because I do get lots of complements about signal and audio quality working from here with "cheap charly" headset and free not soegood connection from Hilton Moscow....
Title: Re: Win7Pro 64
Post by: roland on 2013-02-05, 20:12:58
Great that you have all working as it should  :D
Title: Win7 Home Premium 64bit
Post by: dj3ng on 2013-02-11, 21:58:18
Seem to be the same problem. After update to 1.63 I don´t have virtual comports... What shall I do ...  ? 

DJ3NG, Sigi


After hour´s :
Problem solved manually !
 
Title: Re: Win7Pro 64
Post by: roland on 2013-02-12, 07:21:07
Good good. I did see this post to late then :)
Title: Re: Win7Pro 64
Post by: SM0HXB on 2013-02-12, 10:58:34
Just for information ...

I have the same problem. There are no virtual comports after installing 1.6.3.
Uninstalled as instructed the previous version before installing 1.6.3.
Have tried several times with the same result.

I re-installed version 1.6.0 and everything is okay again. So I keep that version.

Run Windows 7 Pro 64 bit

/Göran
Title: Re: Win7Pro 64
Post by: roland on 2013-02-12, 13:49:36
We are looking into this problem which seems to be caused by the new set of Serial Driver which are needed for Win8.
Title: Re: Win7Pro 64
Post by: roland on 2013-02-14, 16:17:16
Latest news on this.

First of all. The Microbit Comports will not be visible in the Control Panel Device Manager until they are used.
That's a new behavior. So don't worry if you don't see them directly after an installation. They will show up when they are used.

Secondly. I found that a clean install works fine.
However an update from a previous version 1.6.1 or older has an error.
This will be fixed in later releases. This error can be solved quite easy by following this procedure.

Workaround: