Messages

1

Hardware, Cabling, Installations / Re: Microbit setup manager cannot see RRC control unit

« on: 2014-01-14, 17:39:27 »

I bought it from Elecraft as part of their package.

2

Hardware, Cabling, Installations / Re: Microbit setup manager cannot see RRC control unit

« on: 2014-01-10, 20:50:43 »

I have upgraded firmware in both units to 2.75. Still no connection through USB. Not sure about USB connector
 but cable does feel loose in connector.

3

Hardware, Cabling, Installations / Re: Microbit setup manager cannot see RRC control unit

« on: 2014-01-10, 18:15:26 »

Yes. I can browse the control RRC and control the radio through the radio RRC

4

Hardware, Cabling, Installations / Re: Microbit setup manager cannot see RRC control unit

« on: 2014-01-10, 17:20:22 »

Firmware in Radio unit is 007 2.72.
Since I cannot connect microbit to RRC Control unit, I cannot read or update the firmware. I am almost positive, it is the same as the radio unit.

5

Hardware, Cabling, Installations / Re: Microbit setup manager cannot see RRC control unit

« on: 2014-01-10, 16:35:02 »

Thanks Mitch and Jan
I reinstalled Microbit and now have v. 1.25. Nothing has changed. When I connect to radio RRC, everything fine and four virtual ports created. When I connect to control RRC no connection and, of course, no virtual ports created.

Thanks
Alan/N3AD

6

Hardware, Cabling, Installations / Microbit setup manager cannot see RRC control unit

« on: 2014-01-10, 03:13:15 »

I have connected USB cable from RRC control unit to computer USB port. Microbit shows Unknown disconnected!. I have tried several USB ports and a different cable. I then tried a different computer and still no connection. Is it possible I inadvertently changed a setting which is causing this? In every other way the system is working.

Thanks
Alan/N3AD

7

Configuration of Routers, Firewalls, etc / DDNS setup issues

« on: 2013-10-02, 22:49:42 »

I have resolved a number of setup issues I had yesterday. Here is what still needs resolving.
I registered with ddns.remoterig.com which automatically put in the dynamic ddns info, so I think I'm good there.

Issues remaining
1. On the remote radio page, auto connect is set at no. When I change it to yes, it reverts back to no. Should it be no with the ddns activated?
2. Do I need to set ddns in my router to remoterig.com? My router does not that have that option, only show disable, dyndns.org and tzo.com. I dont see any way of entering it manually. If this setting is needed, do I need to update firmware. I've been trying to do that and the upgrade will not accept the files I've downloaded from Lynsys but the installer won't accept it.
3. I am showing ipV4 connectivity but no ipV6 connectivity. Do I need ipV6?

Thanks and 73
Alan/N3AD

8

Configuration, RRC 1258 / Re: Set sip password now locked out

« on: 2013-10-01, 20:26:57 »

Thanks Jan
When I try to get into the radio RRC it asks for user name and password. I have tried get DDNS but not sure of hostname. Is it ddns.remoterig.com? That shows nothing found. Do you know what i should enter as user name on the login. I know the password but didn't create a user name.

Thanks
Alan

9

Configuration, RRC 1258 / Set sip password now locked out

« on: 2013-10-01, 19:39:31 »

I am working through setting my ip settings. But at some point, I think after I registered with Microbit DynDNS. (Not sure if I'm actually registered) I set a password which I do have, but the login is also asking for a username which i have no idea of. I didnt set one. is it related to the serial number?

I also have some issues with ip setup, but need to resolve this first.

Thanks and 73
Alan/N3AD