Messages

1

General discussion forum / WSJTX SuperFox and RCC

« on: 2024-07-22, 17:19:29 »

Since years WSJTX runs fine with my IC7100 via RCC 1258
The new version with SuperFox has problems to take over the frequency of the rig into the computer ; message : Hamlib Error
The only way to solve the the problem is to use e.g. FlRig for rigcontrol instead of the direct IC7100 configuration
any other ideas ?

2

General discussion forum / Re: Update

« on: 2023-09-13, 09:45:36 »

it works ! but the status signal is a bit confusing.

3

General discussion forum / Re: Update

« on: 2023-09-11, 08:35:12 »

now back to 4.59 again and it works fine as usual

4

General discussion forum / Re: Update

« on: 2023-09-11, 08:31:08 »

I get this message :

Wrong file type, got WebSwitch 1216H HAM, expected -1
Click here to clear

5

General discussion forum / Re: Update

« on: 2023-09-11, 08:23:45 »

gm Jan, now it is announced as 4.91 ....strange ...

He the system info :

Company   Microbit
Product   1216H WebSwitch
Model   HAM
Software   4.59
Hardware   1
Bootloader   1.9
Build   Dec 10 2019 13:16:00
S/N   1732
PID   4
Uptime   0 Days, 18 Hours, 48 Mins, 51 Secs
========================================   
MAC   00:1e:fd:00:c4:9c
IP address   192.168.200.75
Netmask   255.255.255.0
Gateway   192.168.200.1
DNS   192.168.200.1
========================================
Max available memory   18301
DNS status   OK, remoterig.com = 86.107.103.218
Dynamic DNS status   Unknown
NTP status   OK, next sync in 15823 secs (Tx 5041 Rx 5041)
Ping status (watchdog)   OK [1 ms]
Active profile   IC 7100
Last WD Reset   5
TCP Error counter   1
Webserver   1

6

General discussion forum / Update

« on: 2023-09-10, 10:12:42 »

Hi, you have announced an update Version 4.92  May, 10th
but I can find only  4.91 May, 10 th
I have installed it and got a short warning; but it is working

Back to version 4.59 again
 
73, Hans, DK3PZ

7

General discussion forum / 1216H Antenna Selction disconnect timeout

« on: 2021-07-29, 17:55:50 »

Product   1216H WebSwitch
Model   HAM
Software   4.59
Hardware   1
Bootloader   1.9
Build   Dec 10 2019 13:16:00
S/N   1732
PID   4

Since some time the timeout disconnect doesn`t work properly after switching OFF the rig (IC7100)
Using "Automatic Control" for different antennas and I only can force "OFF" by pushing the button "ALL OFF"  but still shows a value "Current Frequency"

Any solution ?   73, Hans

8

Configuration, Webswitch 1216H / Re: Automatic Antenna Selection

« on: 2019-06-12, 15:45:55 »

Thanks for Software Update 4.51

It is working fine

73, Hans

9

Configuration, Webswitch 1216H / Re: Automatic Antenna Selection

« on: 2019-06-12, 09:37:49 »

It is working ok now !
Update did not take over the value for Serial A Bd and after changing it to 9600 Bd the automatic antenna selction is working fine again

73, Hans

10

Configuration, Webswitch 1216H / Automatic Antenna Selection

« on: 2019-06-10, 09:42:50 »

Hi, I just made an update (Web Switch) from Ver. 4.11  to Ver. 4.47 and now the automatic antenna selection is out of order; ICOM Adress still the same and I can`t find changes in other settings
Bootloader 1.9
After changing back to Ver. 4.11 everything works ok again

hw nw ?

73, Hans, DK3PZ

11

Configuration, Webswitch 1216H / Re: 1216H CI-V configuration

« on: 2017-03-06, 18:16:49 »

Thanks Mike,
using WS at the remote side for antenna selection and will fed the bus via CI-V Interface and RCC 1258 COM2 to the control side to use it with WSJT-X for frequency control
The program does not ask for any CI-V adress.... so I can keep it as you mentioned before

73, Hans

12

Configuration, Webswitch 1216H / 1216H CI-V configuration

« on: 2017-03-06, 15:02:24 »

From where I can get the value for the second configuration row  = "e1" ; first row "48" is the CI-V adress of my IC706 used for automatic antenna selection

Function Type                       = '4'
ICOM CI-V/XK2000 Transc. Addr.(hex) = '48'
ICOM CI-V/XK2000 Contr. Addr.(hex)  = 'e1'

73, Hans

13

General discussion forum / Re: CI-V Interface

« on: 2016-07-30, 13:56:48 »

ok...many thanks ....73, Hans

14

General discussion forum / Re: CI-V Interface

« on: 2016-07-30, 10:37:27 »

you are welcome Mike !
 but there is no information how to connect both : 1332 CI-V togeather with the automatic antenna selection of the webswitch 1216H
is it possible to connect both in parallel ?

73, Hans

15

General discussion forum / CI-V Interface

« on: 2016-07-29, 13:45:00 »

I am using the CI-V port from my IC 7100  togeather with the Webswitch 1216H for an automatic antenna selection at the remotelocation.
How would it be possible to use the new CI-V Interface also to get the informations to the control side ?