Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Vk7wh

Pages: [1]
1
Thanks Mitch for your suggestions. I forgot to mention that I did try increasing the rx buffer to 6 and the rx delay to 5 with no effect, but I  didn't try the higher figures you suggest. I will let you know how I get on with your suggestions. Incidently, the 2K-FA arrived just before I left on my holiday, so I haven't had a chance to fire it up yet. I will let you know how I go with the serial control.

Thanks again for your helpful suggestions, Mitch

Winston VK7WH

2
I am currently on holidays and been experimenting working my home rig remotely, using a TS-480 front Panel via both 3G and 4G at the control site with a pair of 1258 Mark IIs. I am using a Netcomm 3G/4G Wireless N150 Router 3GM2WN with a Telstra 4G USB Modem.

Having set everything up at home before I left the system worked OK apart from difficuly in initially establishing  a connection and at times, especially during weekends, drop outs on transmission due to poor upload speed. As I live in the countryside, this was not unexpected. The system is rock solid with an ADSL2+ connection.

The first site I tried on my trip I experienced very poor results which again were caused by an absolutely terrible 3G service with upload speeds varying from about 1Mbit/s to as low as 10Kbit/s!

When I tried the next location I visited I was encouraged to note that a fairly good 4G service was available. Download speed varied between 15Mbit/s down to a low of about 5Mbits/s and upload from a top of 7.5Mbits/s down to around 1Mbit/s. When connected, the service is again rock solid, with very good audio reports, but again I have trouble connecting. It usually takes from 2-3 minutes up to 10 minutes to get audio connected. I just have to keep switching it on and off until I get audio through. Sometimes changing band or using the PTT will trigger it. Once connected it remains so.

The only difference I can see in the Control RRC Set Up readings is when it is working:

SIP/STATUS = CONNECTING/TRANSFERRING
RTP STATUS = EXCELLENT (59)

During the time I am trying to connect:

SIP/STATUS = FAULTY (SEE BELOW)
RTP/STATUS = STALLED (20)

All other details on the setup page are the same in both conditions.

I can use the system as it is, however I would be very grateful is anyone has suggestion as to how I can overcome this annoying issue. My knowledge on networks, I am afraid, is reaching its limits.

Many thanks de Winston VK7WH

3
General discussion forum / Re: Expert 2K-FA
« on: 2012-08-24, 12:57:07 »
Hi again Nicola, the Amp arrived a few days before I went on holidays early in August, so I didn't have time to make up the cables and test the serial port before I left. I will be home early in September and will let you know as soon as I test it.

Sorry for the delay. 73 de Winston VK7WH

4
General discussion forum / Re: Expert 2K-FA
« on: 2012-07-23, 12:49:19 »
Hi Nicola. I ordered a 2K-FA in early March and it arrived in Australia last week. Although I have not yet received delivery (it should arrive in the next week or so) I have been assured that my unit DOES have the new serial control port.

I have already received the documentation from the local distributer, 2K-FA Manual ver 2.0 in PDF, which confirms that it does have a serial port. It was shipped in mid July, so I presume that any unit shipped after this date will have the serial port.

As soon as I get the chance, I will test it with my pair of RomoteRig 1258MarkII RRCs and TS480 and let you know, however I am sure it will interface ok

73

Winston VK7WH

Pages: [1]