Messages

1

Configuration, Webswitch 1216H / Re: Controller Steppir + Spe 1.3 k

« on: 2021-02-02, 15:04:57 »

So the RC1261H only serves to manage one thing ... I was wondering why I have been using the RRC1258 MKII pair with Icom 7100 radio for a long time and it works perfectly, I manage my Expert SPE1.3k FA with a simple Ethernet / Com RS232 converter made via web and IP port of my ddns with Expert software but I thought that I would have simplified everything by managing Radio, Amplifier and Antenna with the purchase of the RC-1216H.

2

Configuration, Webswitch 1216H / Controller Steppir + Spe 1.3 k

« on: 2021-02-02, 01:37:06 »

Hi, I would like to ask you if it is possible to remotely manage both Steppir antenna and Spe 1.3 k amplifier with just one 1261H , and control them with the same web interface? Thanks in advance

3

General discussion forum / Re: SunSDR2 PRO + RemoteRig

« on: 2020-10-20, 21:50:51 »

Hi Dan ... Did you finally get it to work?

4

Hardware, Cabling, Installations / Re: USB as COM0 (for N1MM)

« on: 2018-07-14, 00:54:04 »

 Hello Mitch ... I'm sorry if I respond late ... I've been very busy with the work and I'll see if with a clear mind next week I'll do something ... hoping to solve the problem and give a perfect detailed explanation to anyone who wants to use the system .... I will keep you updated
73 Marcello IT9QGH

5

Hardware, Cabling, Installations / Re: USB as COM0 (for N1MM)

« on: 2018-07-12, 02:54:17 »

Hello Mitch, I followed your explanations but still nothing ... the yaesu twin system (ft950 control and ft5000 radio) does not work ... I repeat the links ... maybe I still did not understand ... Cat cable ft950 ( control) rs232 connected to Com2 RRc control .... Cat cable ft5000 (radio) rs232 connected to Com2 RRc radio.
The RRc control and radio configuration I followed your explanations.
Excuse me but this situation is making me go crazy ... the manual explains how to make the cables (I followed step by step making them) and I configured as the manual says ... in short it works only in Pc (control) and Ft5000 (radio) ... clearly with other configurations for RRC

6

Hardware, Cabling, Installations / Re: USB as COM0 (for N1MM)

« on: 2018-07-11, 15:21:23 »

Thanks Mitch for answering me ... I still have not tried for the fact that I'm already out of my qth and then I have to ask an acquaintance of mine to go to my house and bring the connector db9 to Com1 .... then the rest (RRC radio) I will go to change in serial mode (Com1) mode 7 copying baud rate .... instead in Com2 how should I set?

7

Hardware, Cabling, Installations / Re: USB as COM0 (for N1MM)

« on: 2018-07-10, 01:12:11 »

Hello Mitch ... I'm sorry but I have a similar situation but I can not make anything work ... I use the yaesu twin mode with control radio ft 950 and tx ft5000 radio, I performed the explanation of the manual by connecting the radios on com port 2, speed 38600 and rts disabled ... nothing to do wrong ... but if I use the PC control unit and Ft5000 radio, it works well ... do you have any suggestions?
Thanks 73 IT9QGH Marcello

8

General discussion forum / Re: FT-950 controlled by FT-5000

« on: 2018-06-25, 03:30:15 »

Hello I too would like to use the twin yaesu system but unlike you ... in the sense that Ft5000 is remote and ft950 as a control ... my problem is that instead I can not work and strange thing before leaving 'Italy worked and from here (hb9) nothing ... and I use at the moment the pc radio (Ft5000) configuration and it works perfectly