Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ea5zj

Pages: [1] 2
1
General discussion forum / Re: 1258 audio
« on: 2021-02-18, 11:02:05 »
Hello.
By chance, I am ea5zj, I use remoterig and it also happens to me. Also ... I'm an internet provider for ea5xv. It happens to both of us. We have looked at latencies, which are always less than or less than 30ms. Where we don't have saturated wifi spectrum, and the latency never goes up. Public ip, etc. Would you be kind enough to tell us how to upload the buffer in remoterig? Thanks in advance.

2
Feature Requests / Re: supply power for yaesu MH59 typle mics thru mic jack?
« on: 2020-10-14, 23:51:19 »
Some users have asked before us but with no answer in the forum. This is not good. I think it's an easy solution

3
General discussion forum / Re: MC-85 TS-2000 no work. I need ajust?
« on: 2020-10-14, 22:52:36 »
The problem or drawback is that there is no button available to "connect" or "disconnect" remoterig between radio and control and I must auto-connect the menu.

4
General discussion forum / Re: MC-85 TS-2000 no work. I need ajust?
« on: 2020-10-14, 07:42:48 »
Hello Juan Carlos EA5WA
As you say, when I use Mode4 there is no 8v on pin.
When I use mode 8 if there is voltage on the pin. It should not be like that.
Now I have chosen or selected mode5 ts480 and my roger beep is working, and also my mc-85 works now.
From jumper 2, the voltage drops to 8v instead. without jumper 2 the voltage is 9v.
Everything works now.
I think it should not be like that and remoterig should do that mode 4, for kenwood ts2000 if it had tension in micro.
I have selected mode5 only in CONTROL (not radio) and it works.
It also works if I choose mode5 in Control and Radio. Both devices.
I hope I have helped people who are looking in the forum for information on ts-2000 with mc-60, mc-80, mc-85, or similar, even with roger beep on the mic for vhf contests ha ha ha.
I use a translator.
It is never perfect.
ea5zw jordi.

5
General discussion forum / Re: MC-85 TS-2000 no work. I need ajust?
« on: 2020-10-13, 21:09:54 »
My mc-85 worked perfectly connected to my ts2000. Also my mc-43s containing a beep from Roger, which needs power.
I follow the instructions in the remoterig manual and now, neither of them works, ha ha ha.
Tomorrow I will continue investigating.
Let's see if someone in the forum finds the light.
I use google translator, and it is not perfect.

6
General discussion forum / Re: MC-85 TS-2000 no work. I need ajust?
« on: 2020-10-12, 21:20:10 »
adjunt.

7
General discussion forum / MC-85 TS-2000 no work. I need ajust?
« on: 2020-10-12, 07:17:45 »
Hi everyone. We already have our prosistel rotor and ts-2000 working perfect. Our micro mc-85 direct to the station was working fine, now, with remoterig, it doesn't work. We understand you do not receive food + for it. Neither does our roger beep inside mc-43s for vhf contests. Do we need any adjustments for both of them to work? I have looked at the manual but it says that mc-60 does not need power, but it does not. We buy cable for kenwood from remoterig. Some help? I use google translator, and it is never perfect. EA5ZJ




Control-RRC only: JMP-1 is placed behind the TTL connector. With the strap in place a DC
voltage is feed to the microphone element. All ICOM microphones should be DC-feed.
Dynamic microphones like the ones used by Kenwood should not be DC-feed. HEIL
microphones should not be DC-feed either.

8
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-06, 20:23:18 »
Thanks!!!!!!!
ea5zj@ure.es

9
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-06, 10:17:05 »
Notification Prosistel.  Adjunto at post.  Is a pdf reader.


We have worked with the prosistel Todo works manual, ts-2000 and rotor via RRC.
We had to change 2 and 3 on the remote, that is, null cable. I hope this post is helpful to potential visitors.
Many thanks to those who helped us. Very thankful. EA5ZJ Jordi.

10
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-05, 20:31:43 »
We have tried both. Neither works. Neither install max, nor complete part.
Hopeless. Sorry. Are there any other ideas? For mini usb we can not enter the RRC?
no work. No is ok.

11
Configuration, RRC 1258 / Re: Low volume on local side with speaker
« on: 2020-10-04, 17:21:03 »
Thanks!!!!!

12
Configuration, RRC 1258 / Low volume on local side with speaker
« on: 2020-10-04, 15:11:13 »
Low volume on local side with speaker

We keep working.
When we connect the headset the volume is high, perfect. Very good.
When we connect a simple speaker, it is hardly heard. Very low volume.
We do not have an internal jack as in previous models. How do you adjust or choose speaker mode with new models? We did not find anything in manual.
Thank you

13
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-02, 20:26:42 »
We need to bring or feed 3.3v to the converter.      Have a 5v in pin 6.
Monday, we receive material.
I hope this post, help more people

14
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-02, 09:19:50 »
Another.

15
Configuration, RRC 1258 / Re: Prosistel PST641 D mini usb port doesn't work
« on: 2020-10-02, 09:19:20 »
Off course,  but no colour.


Pages: [1] 2