Messages

1

Hardware, Cabling, Installations / Re: USB-Connection only usable for Setup Manager

« on: 2011-01-27, 18:32:43 »

I think that my problem is that i use windows xp 64bit...

This device cannot start. (Code 10). Reinstalling did't help. No hint over the event manager ...

73 - Uwe

2

Hardware, Cabling, Installations / USB-Connection only usable for Setup Manager

« on: 2011-01-25, 21:14:17 »

Hello,
i can use the usb-connection for the setup manager but not for other features like cw-keying.
Following error message i found in the hardware manager:

"There was a probleme installing this hardware: Microbit RRC Virtual Comport, This device can not start (Code10)."

Any hints are welcome... OS is Windows XP SP3. No probs with other usb devices.

73 - Uwe
DK3WW

3

General discussion forum / Re: Network Noise Problems

« on: 2011-01-21, 12:56:39 »

OK Mike,
sorry for my inaccurate description. The remote qth is used by several members of our club. The operating configuration is the following:

We are using a TS480 cofiguration with
RRC-radio side with Firmware 2.10 and the control side with Firmware 2.10 or 2.12  ---> all OK.

Since we had increased the firmware at the control side to 2.33 we have all the same problem with --> network noise.

It comes from the speaker of the ts480 panel if the connection to the radio side was carried out ( also without AF  level ). My friend Holger, DL7AU will renew the Firmware on the radio side today. So we hope that this problem will be solved with the new firmware 2.33 on the radio side...

What do you mean, Mike?

73 - Uwe
DK3WW

4

General discussion forum / Re: Network Noise Problems

« on: 2011-01-21, 09:03:26 »

Hello Mike, 
no, this isn't correct.  I use a rope router of AVM Fritz!Box Fon 7270.  Everything is clean if I connect the RRC from Andy, DL5CW. I use the same configuration but the Firmware is older in Andys RRC and the hardware rev. is 4. In my RRC i installed the newest Fw yesterday and it hase the hardware rev. 5. What can i do? The reset has changed nothing... The noise is terrible in my own RRC.

HW? 73 - Uwe
DK3WW

5

General discussion forum / Re: Network Noise Problems

« on: 2011-01-20, 11:46:57 »

Hello ahain,
yesterday I tested another RRC-1258 MKII (borrowed from DL5CW). The result was: All OK, no more noise. Is my remote box defect or is it the newest firmware i have installed some days before?
The next step is to test a complet reset of my control box. I will test it tonight and then i will report the results.

73 - Uwe
DK3WW
 

6

General discussion forum / Re: Network Noise Problems

« on: 2011-01-11, 22:47:38 »

My last test was to switch off all network devices in my flat. I used the Fritzbox router and the RRC only. But nothing has changed... :-(

73 - Uwe
DK3WW

7

General discussion forum / Re: Network Noise Problems

« on: 2011-01-11, 11:34:56 »

Thank you Mitch for your fast answer.
I have already tested all ethernet settings. The noise don't change.
I am running 100 FDX at present.
I use wlan  in my flat with repeaters in addition to the LAN.
I will switch off all these devices next time and looks, what changes.
My idea was to hear Amateurradio Stations again with remote operation because I have strong local noise from my naiborhood.
Unfortunately, the problems have got more. I remain optimistic and will find the main interference source.

73 - Uwe
DK3WW

8

General discussion forum / Re: Network Noise Problems

« on: 2011-01-11, 09:21:29 »

Hello, i have the same problem here. It comes definitely from the control side. Two other friends of our club can use the remote connection to the radio without these noise problems. I have changed the router ( AVM Fritz!Box Fon 7170 ) to a netgaer router but nothing has changed.
Who can help?
73 - Uwe
DK3WW